Yaskawa DI-16H2 Manuel d'utilisateur télécharger pdf

Yaskawa Electric America, Inc-www.drives.com

02Y00025-0400 Page 1 OF 5

REL. 05/21/96

For GPD 515/G5

Adjustable Frequency Drives

DIGITAL REFERENCE CARD (DI-16H2)

MODEL DS016

Before installing this option, a TECHNICALLY QUALIFIED INDIVIDUAL, who is familiar with this type of

equipment and hazards involved, should READ this ENTIRE INSTRUCTION SHEET.

IMPORTANT

This option may have been installed by the factory. However, certain steps can

only be completed at the installation site. Therefore, review and then perform

those steps which complete the installation process.

INTRODUCTION

When installed, this option allows the user to interface a 16-bit digital speed reference to the GPD 515/G5. This

reference can be binary, BCD(Hz) or BCD(%), with SIGN and SET (read) inputs. (Refer to the GPD515/G5

technical manual description of parameter F3-01.)

CAUTION

THIS OPTION CONTAINS CMOS IC CHIPS (ELECTROSTATIC

SENSITIVE DEVICES). PERSONNEL SHOULD BE GROUNDED

BEFORE REMOVING CONTENTS FROM THE CARTON AND

INSTALLING INTO THE EQUIPMENT.

INSTALLATION

1. Disconnect all electrical power to drive.

2. Remove drive front cover. Check that CHARGE indicator lamp inside drive is off.

3. Verify voltage has been disconnected by using a voltmeter to check for voltage at incoming power terminals

(L1, L2, L3).

WARNING

HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR

DEATH. LOCK ALL POWER SOURCES FEEDING DRIVE IN

"OFF" POSITION.

4. See Figure 2. Install the option on the Main Control Board, 1PCB, and ensure 2CN is properly connected.

Make sure Electrostatic procedure is followed.

1 2 3 4 5

Résumé du contenu

Page 1 - MODEL DS016

Yaskawa Electric America, Inc-www.drives.com02Y00025-0400 Page 1 OF 5REL. 05/21/96For GPD 515/G5Adjustable Frequency DrivesDIGITAL REFERENCE CARD (DI

Page 2 - (DI-16H2) MODEL DS016

5. Connect the grounding lead wire from the DI-16H2 card to terminal 12 on the Control Board.6. Wiring. See Figure 3 and Tables 2 & 3 fo

Page 3

Figure 2. Installation of Digital Reference Card (DI-16H2) in GPD 515/G5Table 3. Terminal Functions of DI-16H2Terminal Pin FunctionBlock No. Binary

Page 4

Figure 3. Interconnection for Digital Reference Card (DI-16H2) Circuit2CN 2CNTC112GPD 515DI-16H2 CARDL1L2L3T1T2T3D0TRANSISTOROPEN COLLECTOROUTPUT M

Page 5

IMPORTANTThe DI-16H2 input circuits can receive output of relay contacts or transistor (open collector).– Use relays with highly reliable contacts (f

Plus de documents pour Équipement YASKAWA DI-16H2

Voir le document Yaskawa DI-16H2 Manuel d'utilisateur

Yaskawa DI-16H2 Manuel d'utilisateur (4 pages)

Commentaires sur ces manuels

Pas de commentaire

Yaskawa DI-16H2 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Yaskawa DI-16H2. Yaskawa DI-16H2 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Équipement YASKAWA DI-16H2

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa DI-16H2