Yaskawa J1000 AC Drive Manuel d'utilisateur télécharger pdf

The following

procedure is a

supplement to other

documentation

supplied with this

equipment and will

guide the user in

properly wiring the

J1000 and motor. It

will also allow the

installer to check

motor direction and

correct if necessary.

Danger:

Improper

wiring can and will

cause

bodily harm

as well as damage

to the equipment

When installing the

system be sure to

follow good wiring

practices and all

applicable codes.

Ensure that the

mounting of the

various components

are secure and that

the environment,

such as extreme

dampness, poor

ventilation etc. will

not cause system

degradation.

Please read this

sheet and the J1000

Quick Start Guide

(TOEPC71060626)

thoroughly before

attempting

any

installation.

OVERVIEW

To make sure you received the correct model it is essential

to verify the J1000 nameplate with your order; and make

sure that the drive has the correct rating so it can be used

with your motor. Please check the nameplate information

as shown in the example below.

 Check that the available power meets the input power

requirements.

 Ensure that the output power from the VFD is

compatible with the motor requirements.

Mounting the J1000

The mounting of the J1000 is extremely important regarding

environment and accessibility. Depending on your system,

there are various models available and therefore the

mounting dimensions (footprint) may be different. Because

the mounting procedure is fairly extensive, it is beyond the

scope of this document, the user is referred to the J1000

Quick Start Guide (Manual No. TOEPC71060626) received

with the J1000, Section 2 Mechanical Installation. Match

up the model that you received and follow the procedure

described in the manual to ensure a safe and functional

installation. In the case where the system has more than one

J1000 refer to the proper clearances required for adequate

ventilation. Please pay particular attention to:

 The clearances to be maintained around the enclosure

for adequate ventilation.

 The environmental specifications such as avoiding

excessive dampness, extreme temperatures, chemical

exposure, corrosive areas etc. to avoid damage to the

equipment and to maintain safety.

Removing Protective Covers

Improper removal of the J1000 front cover and terminal

cover can cause extensive damage to the J1000. To avoid

damage to these items, please pay particular attention to the

J1000 Quick Start Guide, Section 3.5, Protective Covers.

 In the case of systems with multiple VFDs follow this

procedure for each VFD and motor connected.

IP20 / Open Chassis

Remove the Front Cover

Remove the Terminal Cover

U/T1 V/T2 W/T3

3Ø Induction

motor

1Ø Input

Power

Connect

frame to

ground

Input

Protection

(Fuse or C.B.)

To change direction of

motor rotation swap any

two of the three motor

leads (See Step 2)

Fig. 1:

Input Power and Output Motor Electrical

Connections for Single Phase Input J1000

WARNING DO NOT CONNECT ANY OF THE

FOLLOWING TERMINALS TO EARTH GROUND

SINGLE PHASE

INPUT J1000

(R/L1) (S/L2)

(U/T1)

(V/T2)

Connect to

chassis

ground

Fig.1 & 2 below show the electrical connections for the

input power and motor terminals for various J1000 Drive

Models. Select the proper diagram for the single or three

phase model you are installing (see Step 1) and WITH

POWER OFF make the appropriate connections.

Make sure to follow good wiring practices and all

applicable codes. Ensure that the equipment is

grounded properly as shown.

DANGER, LETHAL VOLTAGES ARE PRESENT- Before

applying power to the J1000, ensure that all protected

covers are fastened and all wiring connections are

secure. After the power has been turned OFF, wait at

least five minutes until the charge indicator

extinguishes

completely before touching any wiring,

circuit boards or components.

R/L1 S/L2

U/T1 V/T2 W/T3

3Ø Induction

motor

3Ø Input

Power

Connect

frame to

ground

Input

Protection

(Fuse or C.B.)

To change direction of

motor rotation swap any

two of the three motor

leads (See Step 2)

Fig. 2:

Input Power and Output Motor Electrical

Connections for Three Phase Input J1000

(R/L1) (S/L2)

(T/L3)

(U/T1)

(V/T2)

(W/T3)

Connect to

chassis

ground

R/L1 S/L2

T/L3

B1 B2

+1 +2

(W/T3)

THREE PHASE

INPUT J1000

Step

J1000 Model Identification and

Mounting

Connect Motor and

Line Power

Step

Check Motor Direction

How to Change Parameters

Fig. 3 Digital Operator

Next, press the

Using Safety precaution, and referring to Fig.1 or 2, swap any two

of the three output leads to the motor (U/T1, V/T2 and W/T3). After

the wiring change, repeat Step 3 and recheck motor direction.

After the power has been turned OFF, wait at least five

minutes until the charge indicator extinguishes completely

before touching any wiring, circuit boards or components.

DANGER

If motor rotation is not correct, then power down the J1000 Drive.

should turn on.

Key on the Digital Operator; the green LED

In this step the motor is checked for proper direction and

operation. This test is to be performed solely from the

digital operator. Apply power to the J1000 after all the

electrical connections have been made and protective

covers have been re-attached. At this point, DO NOT RUN

THE MOTOR, the Digital Operator should display as

shown below in Fig. 3.

Next, press the

key on the Digital Operator once, then press

button.the

Next, press the

key on the Digital Operator. The motor

should now be operating at low speed running in the correct forward

(clockwise) direction.

Next, press the key on the Digital Operator.

REV LED

OFF

First Digit Flashing

Digital Operator

turned off.

This step shows how to access and modify a J1000 parameter as

well as how to monitor J1000 signals such as output frequency

and motor current. Make sure all protective covers have been re-

attached and power is turned on. DO NOT RUN THE MOTOR.

Press the

key once.

key.

The digital operator shows the parameter

menu (PAr) then press the

J1000 Digital Operator power-up state

Press the key to select the digit

you would like to change. Next use the

and keys to select the

parameter group, sub-group or number

Modify the parameter value using the

and key and press

the key to save the new value.

Access Parameter Menu and Change Parameter Value

Monitor Motor Frequency and Motor Current

Press the key until the FOUT

LED turns on. The display now shows

the actual drive output frequency in Hz.

Pressing the key again will

show the motor output current. The ‘A’

behind the value means ‘Amps’.

Please refer to the technical manual

on how to access other drive signals.

J1000 Digital Operator power-up state

Motor Current

Output Frequency

Change Parameter Value

Select Parameter

Select Parameter Menu

Page 1 of 2

J1000 AC Drive

Quick Start Procedure

1 2

Résumé du contenu

Page 1 - Quick Start Procedure

The following procedure is a supplement to other documentation supplied with this equipment and will guide the user in properly wiring the J1000 and m

Page 2

Step5This step shows how to setup the sequence and reference method of the J1000. The sequence method determines how the J1000 drive receives its star

Commentaires sur ces manuels

Pas de commentaire

Yaskawa J1000 AC Drive Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Yaskawa J1000 AC Drive. Yaskawa J1000 AC Drive User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa J1000 AC Drive