Yaskawa DS391 Manuel d'utilisateur télécharger pdf

DWG. NO. 02Y00025-0297

SHEET NO. 1 OF 7

REL. 01/30/91 (m-df)

For GPD 515 and GPD 503

Adjustable Frequency Drives

and VCD 703

Vector Control Drives

C H A N G E R E C O R D

STD-6155 8-9-95

STD-4687 3-1-91

STD-6491 4-16-96

STD-4852 6-19-91

STD-5872 8-23-94

ANALOG MONITOR (8-BIT) (AO-08)

MODEL DS390

ANALOG MONITOR (12-BIT) (AO-12)

MODEL DS391

Before installing this option, a TECHNICALLY QUALIFIED INDIVIDUAL, who is familiar with this type of

equipment and hazards involved, should READ this ENTIRE INSTRUCTION SHEET.

IMPORTANT

This option may have been installed by the factory. However, certain steps can

only be completed at the installation site. Therefore, review and then perform

those steps which complete the installation process.

INTRODUCTION

When installed, either of these options allows the user to employ precision analog signals to monitor outputs of

the GPD 515 (U1-01, 02, 03, 05–09, 15–24, 26 & 27), the GPD 503 (output frequency, output current, output

voltage, or DC voltage), or the VCD 703 (Un-03, 04, 05, 21-41, 44).

CAUTION

The option card uses CMOS IC chips. If proper electrostatic discharge (ESD)

protective procedure is not used when handling the card, the ICs may be damaged,

resulting in erratic performance of the drive.

INSTALLATION

1. Disconnect all electrical power to drive.

2. Remove drive front cover. Check that CHARGE indicator lamp inside drive is off.

3. Verify voltage has been disconnected by using a voltmeter to check for voltage at incoming power terminals

(L1, L2, L3).

WARNING

HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR

DEATH. LOCK ALL POWER SOURCES FEEDING DRIVE IN

"OFF" POSITION.

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - MODEL DS391

DWG. NO. 02Y00025-0297SHEET NO. 1 OF 7REL. 01/30/91 (m-df)For GPD 515 and GPD 503Adjustable Frequency Drivesand VCD 703Vector Control DrivesC H A N

Page 2 - REL. 01/30/91 (m-df)

DWG. NO. 02Y00025-0297SHEET NO. 2 OF 7REL. 01/30/91 (m-df)Refer to Sheet 1 for latest change.Figure 2. Installation of Analog Monitor (AO-08) or (AO

Page 3 - (1) (2) size M3

DWG. NO. 02Y00025-0297SHEET NO. 3 OF 7REL. 01/30/91 (m-df)Refer to Sheet 1 for latest change. Table 1. SpecificationsParameter Analog Monitor (AO-0

Page 4 - SHEET NO. 4 OF 7

DWG. NO. 02Y00025-0297SHEET NO. 4 OF 7REL. 01/30/91 (m-df)Refer to Sheet 1 for latest change.Figure 3. Interconnection for Analog Monitor (AO-08 or

Page 5 - SHEET NO. 5 OF 7

DWG. NO. 02Y00025-0297SHEET NO. 5 OF 7REL. 01/30/91 (m-df)Refer to Sheet 1 for latest change. 7. Adjustments. There are no adjustments to be ma

Page 6 - SHEET NO. 6 OF 7

DWG. NO. 02Y00025-0297SHEET NO. 6 OF 7REL. 01/30/91 (m-df)Refer to Sheet 1 for latest change.Table 5. System Constant Sn-28 – Selecting Monitored O

Page 7 - SHEET NO. 7 OF 7

DWG. NO. 02Y00025-0297SHEET NO. 7 OF 7REL. 01/30/91 (m-df)Refer to Sheet 1 for latest change. 8. Reinstall and secure drive cover.9. Place this

Commentaires sur ces manuels

Pas de commentaire

Yaskawa DS391 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Yaskawa DS391. Yaskawa DS391 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa DS391