YASKAWA CDBR Spécifications télécharger pdf (Page 30)

6 Parameter Table

EN 30 YASKAWA Europe TOEP C710616 88A - AC Drive A1000 IP23/54 Floor Standing - Quick Start Guide

C6-02

Carrier

Frequency

Selection

1: 2.0 kHz

2: 5.0 kHz

3: 8.0 kHz

4: 10.0 kHz

5: 12.5 kHz

6: 15.0 kHz

7: Swing PWM1 (Audible sound 1)

8: Swing PWM2 (Audible sound 2)

9: Swing PWM3 (Audible sound 3)

A: Swing PWM4 (Audible sound 4)

B to E: No setting possible

F: User defined (determined by C6-03

through C6-05)

Frequency Reference

d1-01 to

d1-16

Frequency

Reference

1 to 16

Sets the frequency reference for the drive.

Setting units are determined by parameter

o1-03.

d1-17

Jog Frequency

Reference

Sets the Jog frequency reference. Setting

units are determined by parameter o1-03.

V/f Pattern for Motor 1

E1-01

Input Voltage

Setting

This parameter must be set to the power

supply voltage.

WARNING! Drive input voltage (not motor

voltage) must be set in E1-01 for the

protective features of the drive to function

properly. Failure to do so may result in

equipment damage and/or death or personal

injury.

E1-04

Maximum

Output

Frequency

These parameters are only applicable when

E1-03 is set to F.

To set linear V/f characteristics, set the

same values for E1-07 and E1-09. In this

case, the setting for E1-08 will be

disregarded. Ensure that the four

frequencies are set according to these rules:

E1-09  E1-07  E1-06 E1-04

Note: Some parameters may not be

available depending on the control mode.

• E1-07, E1-08 and E-10 are available only

in the following control modes: V/f

Control, V/f with PG, Open Loop Vector.

• E1-11, E1-12 and E-13 are available only

in the following control modes: V/f

Control, V/f with PG, Open Loop Vector,

Closed Loop Vector.

E1-05

Maximum

Vo l t a g e

E1-06

Base

Frequency

E1-07

Middle Output

Frequency

E1-08

Middle Output

Frequency

Vo l t a g e

E1-09

Minimum

Output

Frequency

E1-10

Minimum

Output

Frequency

Vo l t a g e

E1-13 Base Voltage

Motor 1 Parameters

E2-01

Motor Rated

Current

Sets the motor nameplate full load current in

Amps. Automatically set during

Auto-Tuning.

E2-02

Motor Rated

Slip

Sets the motor rated slip. Automatically set

during Auto-Tuning.

No. Name Description

Output Voltage (V)

Frequency (Hz)

E1-05

E1-12

E1-13

E1-08

E1-10

E1-09 E1-07 E1-06 E1-11 E1-04

E2-03

Motor

No-Load

Current

Sets the no-load current for the motor.

Automatically set during Auto-Tuning.

E2-04

Number of

Motor Poles

Sets the number of motor poles.

Automatically set during Auto-Tuning.

E2-05

Motor

Line-to-Line

Resistance

Sets the phase-to-phase motor resistance.

Automatically set during Auto-Tuning.

E2-06

Motor Leakage

Inductance

Sets the voltage drop due to motor leakage

inductance as a percentage of motor rated

voltage. Automatically set during

Auto-Tuning.

Multi-Function Digital Inputs

H1-01 to

H1-08

Multi-Function

Digital Input

Terminal S1 to

S8 Function

Selection

Selects the function of terminals S1 to S8.

Setting H1-03 = 24 (Default) must not be

changed. Fan monitoring function.

Note: Major functions are listed at the end of the table.

Multi-Function Digital Outputs

H2-01

Terminal M1-

M2 function

selection

Set the function for the relay output M1-

M2.

H2-02

Terminal M3-

M4 function

selection

Sets the function for the relay output M3-

M4.

H2-03

Terminal M5-

M6 function

selection

Sets the function for the relay output M5-

M6.

H2-06

Watt Hour

Output Unit

Selection

Outputs a 200 ms pulse signal when the

watt-hour counter increases by the units

selected.

0: 0.1 kWh units

1: 1 kWh units

2: 10 kWh units

3: 100 kWh units

4: 1000 kWh units

Note: Major functions are listed at the end of the table.

Multi-Function Analog Inputs

H3-01

Terminal A1

Signal Level

Selection

0: 0 to 10 V

1: –10 to 10 V

H3-02

Terminal A1

Function

Selection

Sets the function of terminal A1.

H3-03

Terminal A1

Gain Setting

Sets the level of the input value selected in

H3-02 when 10 V is input at terminal A1.

H3-04

Terminal A1

Bias Setting

Sets the level of the input value selected in

H3-02 when 0 V is input at terminal A1.

H3-05

Terminal A3

Signal Level

Selection

0: 0 to 10 V

1: –10 to 10 V

H3-06

Terminal A3

Function

Selection

Sets the function of terminal A3.

H3-07

Terminal A3

Gain Setting

Sets the level of the input value selected in

H3-06 when 10 V is input at terminal A3.

H3-08

Terminal A3

Bias Setting

Sets the level of the input value selected in

H3-06 when 0 V is input at terminal A3.

No. Name Description

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

YASKAWA CDBR Spécifications Page 30

Commentaires sur ces manuels

Produits connexes et manuels pour Adaptateurs et onduleurs de puissance YASKAWA CDBR