YASKAWA VS-606V7 Series Manuel d'instructions Page 133
- Page / 176
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
133
1. Removal
(1) Remove the front cover and
terminal cover, and then remove
the cooling fan connector
(CN10).
(2) Press the right and left clicks of
the fan cover to direction 1, and
pull the fan cover to direction 2
to remove it from the inverter
unit. Pull out the wiring from the
cable lead-in hole at the bottom
of the plastic case.
(3) Open the right and left sides of
the fan cover to remove the
cover from the cooling fan.
2. Mounting
(1) Mount the cooling fan on the fan
cover. The arrow mark to
indicate the wind direction must
be opposite to the cover.
(2) Mount the fan cover on the
inverter. Be sure to mount the
right and left clicks of the fan
cover on the heatsink. Lead in
the wiring from the cable lead-in
hole at the bottom of the plastic
case to the inside of the inverter.
(3) Connect the wiring to the cooling
fan connector (CN10) and mount
the front cover and the terminal
cover.
• Inverter of W-dimension (width) 108mm (4.25 inches)
COOLING
FAN WIRE
WIND DIRECTION
- INSTRUCTION MANUAL 1
- General Precautions 2
- NOTES FOR SAFE OPERATION 3
- WARNINGS FOR UL/cUL MARKING 4
- WARNINGS FOR CE MARKINGS 4
- RECEIVING 5
- MOUNTING 5
- OPERATION 8
- MAINTENANCE AND INSPECTION 9
- WARNING DISPLAY 11
- 1. RECEIVING 16
- 2. IDENTIFYING THE PARTS 17
- TERMINAL RESISTOR SWITCH 18
- FOR COMMUNICATION CIRCUIT 18
- VOLTAGE/CURRENT CHANGE 18
- SWITCH FOR ANALOG 18
- FREQUENCY REFERENCE INPUT 18
- ∗C20P1 to 20P7, B0P1 to B0P4 19
- ∗C24P0, B2P2, 43P0, 44P0 19
- 3. MOUNTING 20
- Mounting Dimensions 21
- 4. WIRING 24
- • m (Ib • in) 25
- Wiring the Main Circuit 28
- Wiring the Control Circuit 29
- Wiring Inspection 30
- 5. OPERATING THE INVERTER 31
- (Forward) 32
- (Reverse) 32
- >< 33
- LED Description 35
- Multi-Function monitor 36
- • Monitoring 37
- Data reception error display 38
- Simple Data Setting 40
- 6. PROGRAMMING FEATURES 41
- Using V/f Control Mode 42
- (VOLTAGE) 44
- Using Vector Control Mode 45
- STANDARD V/F 47
- HIGH STARTING TORQUE V/F 47
- LOCAL mode REMOTE mode 48
- Selecting Run/Stop Commands 49
- +12V, 20mA 51
- (0 TO +10V) 51
- FREQUENCY 51
- SETTING POWER 51
- Gain n060 = 200 53
- Bias n061 = 0 53
- MAX. FREQUENCY (100%) 54
- Using four accel/decel times 55
- S-curve characteristics in 57
- FREQUENCY REFERENCE 61
- AGREED SPEED 62
- DETECTION 62
- Pulse monitor output 65
- Used as a sourcing output 66
- Used as a sinking input 66
- Wiring Distance between 68
- Inverter and Motor 68
- Selecting Stopping Method 70
- Using input signals 72
- ( ) 73
- D1UU UHH H H H HDD D 74
- Analog input level 77
- Ref.page 78
- Current reference selection 81
- MOTOR CURRENT 84
- Constants 86
- Motor Protection 87
- Example of 200V class motor 88
- MEMOCON Series 89
- Example of RS-485 89
- VS-606V7 VS-606V7 VS-606V7 89
- P 2 R + R 90
- P C S + S 90
- Function Code 92
- Hexadecimal 92
- Function 92
- Multi-function 98
- Error Codes 99
- S 7 P 1 P 2 R + R 100
- S 4 S C P C S + S 100
- Voltage limit 102
- Upper limit 102
- Lower limit 102
- Output frequency 102
- Output voltage 103
- Voltage fluctuation 103
- Motor Code 105
- Using PID Control Mode 106
- Constant 108
- PID Control Block Diagram 110
- Inverter 111
- Constant read 113
- READ function 114
- Explanation Operator display 116
- Explanation 117
- Operator display 117
- Inverter Capacity Display 118
- Software No. Display 119
- Display List 120
- Item Contents 121
- Loss (n064) 123
- Undertorque Detection 125
- Setting Description 126
- (Note 1) 127
- Periodical Inspection 131
- Part Replacement 131
- Replacement of cooling fan 132
- 1. Removal 133
- 2. Mounting 133
- 8. FAULT DIAGNOSIS 134
- Alarm Display and Contents 135
- Fault Display and Contents 138
- Troubleshooting 143
- 9. SPECIFICATIONS 145
- OUTPUT FREQUENCY 151
- Use sequencer to break 152
- Terminal Description 153
- +24V common: PNP side) 154
- Factory setting: NPN side 154
- VS-606V7 155
- Dimensions / Heat Loss 156
- VS-606V7 model 158
- Constants List 160
- (Note 1) (Note 6) 161
- (Note 5) 161
- (Note 3) 162
- (Note 2) 164
- (note 3) 165
- -100 to 100% 166
- < 200V class 3-phase 169
- < 200V class single-phase 169
- < 400V class 3-phase 170
- Revision History 173
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance YASKAWA VS-606V7 Series
(122 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.211 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels