YASKAWA VS-606V7 Series Manuel d'instructions Page 28
- Page / 176
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Wiring the Main Circuit
28
MCCB or
leakage
breaker
L1 L2 L3
Grounding
•
Braking resistor connection (optional)
To connect the braking resistor, cut the
protector on terminals B1 and B2.
To protect the braking resistor from
overheating, install a thermal overload
relay between the braking resistor and
the inverter. This provides a sequence
which shuts off the power supply, by a
thermal relay trip contact.
Use this same procedure when
connecting a braking resistor unit.
Refer to page 152.
• Inverter output
Connect the motor terminals to U/T1,
V/T2,W/T3.
• Wiring the main circuit terminals
Pass the cables through wiring hole and
connect. Be sure to mount the cover in
its original position.
Connect with a Phillips (plus) screwdriver.
GOOD GOOD POOR
[Example of 3-phase,
400V class, 0.37kW
inverters]
• Main circuit input power supply
Always connect the power supply
line to
input terminals R/L1, S/L2,
and T/L3
[
R/L1, S/L2
for single-phase inverters].
Never connect them to terminal
U/T1,V/T2,W/T3, B1, B2, -, +1, or +2.
Otherwise the inverter may be damaged.
For single-phase inverters, always
use terminals R/L1 and S/L2. Never
connect to terminal T/L3.
• Grounding (Use ground terminal .)
Make sure to ground the ground terminal
according to the local grounding
code.
Never ground the VS-606V7 in common
with welding machines, motors, or other
electrical equipment.
When several VS-606V7 units are used
side by side, ground each unit as shown
in examples. Do not loop the ground
wires.
NOTE
- INSTRUCTION MANUAL 1
- General Precautions 2
- NOTES FOR SAFE OPERATION 3
- WARNINGS FOR UL/cUL MARKING 4
- WARNINGS FOR CE MARKINGS 4
- RECEIVING 5
- MOUNTING 5
- OPERATION 8
- MAINTENANCE AND INSPECTION 9
- WARNING DISPLAY 11
- 1. RECEIVING 16
- 2. IDENTIFYING THE PARTS 17
- TERMINAL RESISTOR SWITCH 18
- FOR COMMUNICATION CIRCUIT 18
- VOLTAGE/CURRENT CHANGE 18
- SWITCH FOR ANALOG 18
- FREQUENCY REFERENCE INPUT 18
- ∗C20P1 to 20P7, B0P1 to B0P4 19
- ∗C24P0, B2P2, 43P0, 44P0 19
- 3. MOUNTING 20
- Mounting Dimensions 21
- 4. WIRING 24
- • m (Ib • in) 25
- Wiring the Main Circuit 28
- Wiring the Control Circuit 29
- Wiring Inspection 30
- 5. OPERATING THE INVERTER 31
- (Forward) 32
- (Reverse) 32
- >< 33
- LED Description 35
- Multi-Function monitor 36
- • Monitoring 37
- Data reception error display 38
- Simple Data Setting 40
- 6. PROGRAMMING FEATURES 41
- Using V/f Control Mode 42
- (VOLTAGE) 44
- Using Vector Control Mode 45
- STANDARD V/F 47
- HIGH STARTING TORQUE V/F 47
- LOCAL mode REMOTE mode 48
- Selecting Run/Stop Commands 49
- +12V, 20mA 51
- (0 TO +10V) 51
- FREQUENCY 51
- SETTING POWER 51
- Gain n060 = 200 53
- Bias n061 = 0 53
- MAX. FREQUENCY (100%) 54
- Using four accel/decel times 55
- S-curve characteristics in 57
- FREQUENCY REFERENCE 61
- AGREED SPEED 62
- DETECTION 62
- Pulse monitor output 65
- Used as a sourcing output 66
- Used as a sinking input 66
- Wiring Distance between 68
- Inverter and Motor 68
- Selecting Stopping Method 70
- Using input signals 72
- ( ) 73
- D1UU UHH H H H HDD D 74
- Analog input level 77
- Ref.page 78
- Current reference selection 81
- MOTOR CURRENT 84
- Constants 86
- Motor Protection 87
- Example of 200V class motor 88
- MEMOCON Series 89
- Example of RS-485 89
- VS-606V7 VS-606V7 VS-606V7 89
- P 2 R + R 90
- P C S + S 90
- Function Code 92
- Hexadecimal 92
- Function 92
- Multi-function 98
- Error Codes 99
- S 7 P 1 P 2 R + R 100
- S 4 S C P C S + S 100
- Voltage limit 102
- Upper limit 102
- Lower limit 102
- Output frequency 102
- Output voltage 103
- Voltage fluctuation 103
- Motor Code 105
- Using PID Control Mode 106
- Constant 108
- PID Control Block Diagram 110
- Inverter 111
- Constant read 113
- READ function 114
- Explanation Operator display 116
- Explanation 117
- Operator display 117
- Inverter Capacity Display 118
- Software No. Display 119
- Display List 120
- Item Contents 121
- Loss (n064) 123
- Undertorque Detection 125
- Setting Description 126
- (Note 1) 127
- Periodical Inspection 131
- Part Replacement 131
- Replacement of cooling fan 132
- 1. Removal 133
- 2. Mounting 133
- 8. FAULT DIAGNOSIS 134
- Alarm Display and Contents 135
- Fault Display and Contents 138
- Troubleshooting 143
- 9. SPECIFICATIONS 145
- OUTPUT FREQUENCY 151
- Use sequencer to break 152
- Terminal Description 153
- +24V common: PNP side) 154
- Factory setting: NPN side 154
- VS-606V7 155
- Dimensions / Heat Loss 156
- VS-606V7 model 158
- Constants List 160
- (Note 1) (Note 6) 161
- (Note 5) 161
- (Note 3) 162
- (Note 2) 164
- (note 3) 165
- -100 to 100% 166
- < 200V class 3-phase 169
- < 200V class single-phase 169
- < 400V class 3-phase 170
- Revision History 173
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance YASKAWA VS-606V7 Series
(122 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.500 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels