Yaskawa iQpump Micro Manuel d'utilisateur Page 142
- Page / 300
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Status Description
Open Output frequency or motor speed and frequency reference are not both within the range of L4-01 ±L4-02.
Closed Output frequency or motor speed and the frequency reference are both within the range of L4-01 ±L4-02.
Note: Frequency detection works in forward and reverse. The value of L4-01 is used as the detection level for both directions.
Frequency reference
Frequency reference + L4-02
Frequency reference – L4-02
L4-01
L4-01 + L4-02
L4-01 – L4-02
Frequency reference
Frequency reference + L4-02
Frequency reference – L4-02
–L4-01
–L4-01 + L4-02
–L4-01 – L4-02
During
Forward
During Reverse
Output frequency
0 Hz
OFF OFF OFF
ON ON
ON
ON
Output frequency
User Set
Speed Agree 1
Figure 4.46 User Set Speed Agree 1 Time Chart
Setting 4: Frequency Detection 1
The output opens when the output frequency rises above the detection level set in L4-01 plus the detection width set in L4-02.
The terminal remains open until the output frequency or motor speed fall below the level set in L4-01.
Status Description
Open Output frequency or motor speed exceeded L4-01 + L4-02.
Closed Output frequency or motor speed is below L4-01 or has not exceeded L4-01 + L4-02.
Note: Frequency detection works in forward and reverse. The value of L4-01 is used as the detection level for both directions.
L4-02
Frequency
detection 1
ON
OFF
L4-02
L4-01
L4-01
Output Frequency
or Motor Speed
Figure 4.47 Frequency Detection 1 Time Chart
Setting 5: Frequency Detection 2
The output closes when the output frequency is above the detection level set in L4-01. The terminal remains closed until the
output frequency or motor speed fall below L4-01 minus the setting of L4-02.
Status Description
Open Output frequency or motor speed is below L4-01 minus L4-02 or has not exceeded L4-01.
Closed Output frequency or motor speed exceeded L4-01.
Note: Frequency detection works in forward and reverse. The value of L4-01 is used as the detection level for both directions.
4.8 Detailed iQpump Parameter Descriptions
142
YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual
- User Manual 1
- Simplex Quick Start Procedure 3
- Table of Contents 29
- Preface & General Safety 35
- Applicable Documentation 36
- Terms and Abbreviations 36
- Trademarks 36
- Selection 39
- Repetitive Starting/Stopping 40
- Installation 40
- Settings 40
- Motor Application Precautions 41
- Specialized Motors 42
- Drive Label Warning Example 43
- Warranty Information 43
- Receiving 45
- PW 2 V 0010 F A A 46
- Mechanical Installation 49
- 2.1 Mechanical Installation 50
- Single Drive Installation 51
- Multiple Drive Installation 51
- 27 mm (1.06 in.) 52
- Voltage Class Drive Model 56
- Dimensions mm (in) 56
- W H D W1 H1 H2 t1 A B E 56
- Electrical Installation 59
- 3.3 Protective Covers 65
- Removing the Top Cover 66
- Reattaching the Top Cover 66
- Select Cable Gland 67
- 3.5 Main Circuit Wiring 70
- Ground Wiring 73
- 3.6 Control Circuit Wiring 75
- Terminal Configuration 76
- 3.7 I/O Connections 79
- 3.8 Main Frequency Reference 81
- 3.9 Wiring Checklist 82
- Start-Up Checklist 84
- 4.2 Powering Up the Drive 86
- Keys, Displays, and LEDs 87
- LED Screen Displays 88
- Frequency Reference 90
- Keys and Displays 92
- LCD Display 93
- ALARM (ALM) LED Displays 94
- Setting the Real Time Clock 95
- 20 1 0/01/01 00:00 96
- Second per month 96
- YYYY/MM/DD HH:MM 96
- Clock Not Set 97
- No Setting (Default) 98
- Initial Display <5> 99
- - MODE - PRG 100
- Programming 100
- Start-Up Programming 101
- & Operation 101
- 14.00 Hz 102
- 4.6 Pump Application Presets 104
- Related Parameters 106
- Current Limit 109
- Functional Operation 110
- R+ R- S+ S 111
- 100.0PSI 112
- U5-99= 100.0 113
- U1-01= 59.41 114
- U1-01= 55.00 114
- U1-01= 51.37 114
- <1> 116
- Triplex System Example 117
- Multiplexing Stop History 118
- A1-01: Access Level Selection 119
- A1-03: Initialize Parameters 120
- DIP switch S1 123
- Figure 5.4 124
- DC Injection brake time 126
- Max. output frequency (E1-04) 126
- E2-01: Motor Rated Current 129
- E2-04: Number of Motor Poles 129
- Analog Signal 134
- Agree 2) 145
- P1-01: Pump Mode 152
- P1-02: System Units 152
- P1-10: Low Feedback Selection 154
- P1-11: High Feedback Level 154
- P2-01: Sleep Level Type 155
- P2-02: Sleep Level 155
- P2-03: Sleep Delay Time 155
- P4-01: Pre-Charge Level 155
- P4-02: Pre-Charge Frequency 155
- P4-03: Pre-Charge Time 156
- P4-17: Utility Start Delay 160
- P4-32: Pre-Charge Level 2 160
- P5-02: HAND Reference 1 161
- This Page Intentionally Blank 162
- Troubleshooting 163
- 5.2 Fault Detection 165
- 5.3 Alarm Detection 180
- Fault Reset Methods 198
- 6.1 Inspection 200
- Periodic Inspection & 201
- Maintenance 201
- 6.2 Periodic Maintenance 202
- Related Drive Parameters 203
- 6.3 Drive Cooling Fans 204
- Cooling Fan Replacement 205
- Installing the Cooling Fan 206
- Required Additional Parts 207
- Internal fan External fan 208
- Installing the Internal Fan 209
- Removing the External Fan 209
- Installing the External Fan 210
- 6.4 Drive Replacement 211
- Connector 214
- Appendix: A 217
- A.1 Power Ratings 218
- Specifications 219
- A.2 Drive Specifications 221
- A.3 Drive Watt Loss Data 223
- A.4 Drive Derating Data 224
- Temperature Derating 225
- Altitude Derating 225
- Appendix: B 227
- A1: Initialization 228
- A2: User Parameters 228
- B.2 b: Application 229
- Parameter List 231
- B.3 C: Tuning 234
- C3: Slip Compensation 235
- C4: Torque Compensation 235
- C6: Carrier Frequency 235
- B.4 d: References 236
- B.5 E: Motor Parameters 239
- E2: Motor 1 Parameters 240
- B.6 F: Options 242
- <1> 244
- H4: Analog Outputs 252
- H6: Pulse Train Input 253
- B.8 L: Protection Function 254
- L3: Stall Prevention 255
- L4: Speed Detection 257
- L5: Fault Restart 257
- L6: Torque Detection 258
- L8: Drive Protection 259
- B.11 P: Pump Parameters 265
- P2: Pump Protection 267
- P4: Pump Advanced 268
- P5: Pump HAND Mode 270
- P7: Anti-Jam 271
- P9: Network Options 271
- Q3: Output Current Limit 275
- Q1: Preset Setpoint 275
- B.13 S: Special Application 276
- B.14 T: Motor Tuning 277
- B.15 U: Monitors 278
- U2: Fault Trace 281
- U3: Fault History 281
- U4: Maintenance Monitors 283
- U5: PID Monitors 285
- U6: Operation Status Monitors 285
- U9: Operation Status Monitors 285
- B.16 Defaults by Drive Model 286
- Appendix: C 291
- C.1 UL Standards 292
- Single-Phase 200 V Class 293
- Three-Phase 200 V Class 293
- Three-Phase 400 V Class 294
- Standards Compliance 295
- Drive Short-Circuit Rating 296
- Revision History 298
Produits connexes et manuels pour Équipement Yaskawa iQpump Micro
Équipement Yaskawa 1000 Series Drive Option - CANopen Technical Manua Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Yaskawa 1000 Series Drive Option - CC-Link Technical Manua Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Yaskawa 1000 Series Drive Option - DeviceNet Installation Manuel d'utilisateur
(37 pages)
(37 pages)
Équipement Yaskawa 1000 Series Drive Option - DeviceNet Technical Man Manuel d'utilisateur
(81 pages)
(81 pages)
Équipement Yaskawa 1000 Series Drive Option - MECHATROLINK-II Install Manuel d'utilisateur
(32 pages)
(32 pages)
Équipement Yaskawa 1000 Series Drive Option - Digital Output Installa Manuel d'utilisateur
(31 pages)
(31 pages)
Équipement Yaskawa 1000 Series Drive Option - MECHATROLINK-II Technic Manuel d'utilisateur
(41 pages)
(41 pages)
Équipement Yaskawa 1000 Series Drive Option - Profibus-DP Installatio Manuel d'utilisateur
(35 pages)
(35 pages)
Équipement Yaskawa 1000 Series Drive Option - Open Collector Type PG Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Yaskawa Z1000U Manuel d'utilisateur
(378 pages)
(378 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels