Yaskawa iQpump Micro Manuel d'utilisateur Page 166
- Page / 300
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Digital Operator Display Fault Name
Cause Possible Solution
Control circuit is damaged
• Cycle power to the drive.
• If the problem continues, replace the drive.
Control circuit terminals have shorted out
(+V, AC).
• Check for wiring errors along the control circuit terminals.
• Correct the wiring.
Check the resistance of the speed potentiometer and related wiring.
Control terminal input current has
exceeded allowable levels.
• Check the input current.
• Reduce the current input to control circuit terminal (+V) to 20 mA.
Digital Operator Display Fault Name
CPF03
PWM Data Error
There is a problem with the PWM data.
Cause Possible Solution
Hardware is damaged Replace the drive.
Digital Operator Display Fault Name
CPF06
EEPROM Memory Data Error
Error in the data saved to EEPROM
Cause Possible Solution
There is an error in EEPROM control
circuit
• Turn off the power and check the connection between the control board and the drive.
• If the problem continues, replace the drive.
The power supply was switched off while
parameters were being saved to the drive
Reinitialize the drive (A1-03 = 2220, 3330).
Digital Operator Display Fault Name
CPF07
Terminal Board Communications Error
A communication error occurred at the terminal board.
Cause Possible Solution
There is a faulty connection between the
terminal board and the control board
Turn off the power and reconnect the control circuit terminals.
Digital Operator Display Fault Name
CPF08
EEPROM Serial Communication Fault
EEPROM communications are not functioning properly.
Cause Possible Solution
Terminal board or control board is not
connected properly.
Turn the power off and check the control terminal connections.
There is a faulty connection between the
terminal board and the control board
Turn off the power and reconnect the control circuit terminals.
Digital Operator Display Fault Name
CPF11 RAM Fault
Cause Possible Solution
Hardware is damaged Replace the drive.
Digital Operator Display Fault Name
CPF12
FLASH Memory Fault
Problem with the ROM (FLASH memory).
Cause Possible Solution
Hardware is damaged Replace the drive.
Digital Operator Display Fault Name
CPF13
Watchdog Circuit Exception
Self-diagnostics problem.
Cause Possible Solution
5.2 Fault Detection
166
YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual
- User Manual 1
- Simplex Quick Start Procedure 3
- Table of Contents 29
- Preface & General Safety 35
- Applicable Documentation 36
- Terms and Abbreviations 36
- Trademarks 36
- Selection 39
- Repetitive Starting/Stopping 40
- Installation 40
- Settings 40
- Motor Application Precautions 41
- Specialized Motors 42
- Drive Label Warning Example 43
- Warranty Information 43
- Receiving 45
- PW 2 V 0010 F A A 46
- Mechanical Installation 49
- 2.1 Mechanical Installation 50
- Single Drive Installation 51
- Multiple Drive Installation 51
- 27 mm (1.06 in.) 52
- Voltage Class Drive Model 56
- Dimensions mm (in) 56
- W H D W1 H1 H2 t1 A B E 56
- Electrical Installation 59
- 3.3 Protective Covers 65
- Removing the Top Cover 66
- Reattaching the Top Cover 66
- Select Cable Gland 67
- 3.5 Main Circuit Wiring 70
- Ground Wiring 73
- 3.6 Control Circuit Wiring 75
- Terminal Configuration 76
- 3.7 I/O Connections 79
- 3.8 Main Frequency Reference 81
- 3.9 Wiring Checklist 82
- Start-Up Checklist 84
- 4.2 Powering Up the Drive 86
- Keys, Displays, and LEDs 87
- LED Screen Displays 88
- Frequency Reference 90
- Keys and Displays 92
- LCD Display 93
- ALARM (ALM) LED Displays 94
- Setting the Real Time Clock 95
- 20 1 0/01/01 00:00 96
- Second per month 96
- YYYY/MM/DD HH:MM 96
- Clock Not Set 97
- No Setting (Default) 98
- Initial Display <5> 99
- - MODE - PRG 100
- Programming 100
- Start-Up Programming 101
- & Operation 101
- 14.00 Hz 102
- 4.6 Pump Application Presets 104
- Related Parameters 106
- Current Limit 109
- Functional Operation 110
- R+ R- S+ S 111
- 100.0PSI 112
- U5-99= 100.0 113
- U1-01= 59.41 114
- U1-01= 55.00 114
- U1-01= 51.37 114
- <1> 116
- Triplex System Example 117
- Multiplexing Stop History 118
- A1-01: Access Level Selection 119
- A1-03: Initialize Parameters 120
- DIP switch S1 123
- Figure 5.4 124
- DC Injection brake time 126
- Max. output frequency (E1-04) 126
- E2-01: Motor Rated Current 129
- E2-04: Number of Motor Poles 129
- Analog Signal 134
- Agree 2) 145
- P1-01: Pump Mode 152
- P1-02: System Units 152
- P1-10: Low Feedback Selection 154
- P1-11: High Feedback Level 154
- P2-01: Sleep Level Type 155
- P2-02: Sleep Level 155
- P2-03: Sleep Delay Time 155
- P4-01: Pre-Charge Level 155
- P4-02: Pre-Charge Frequency 155
- P4-03: Pre-Charge Time 156
- P4-17: Utility Start Delay 160
- P4-32: Pre-Charge Level 2 160
- P5-02: HAND Reference 1 161
- This Page Intentionally Blank 162
- Troubleshooting 163
- 5.2 Fault Detection 165
- 5.3 Alarm Detection 180
- Fault Reset Methods 198
- 6.1 Inspection 200
- Periodic Inspection & 201
- Maintenance 201
- 6.2 Periodic Maintenance 202
- Related Drive Parameters 203
- 6.3 Drive Cooling Fans 204
- Cooling Fan Replacement 205
- Installing the Cooling Fan 206
- Required Additional Parts 207
- Internal fan External fan 208
- Installing the Internal Fan 209
- Removing the External Fan 209
- Installing the External Fan 210
- 6.4 Drive Replacement 211
- Connector 214
- Appendix: A 217
- A.1 Power Ratings 218
- Specifications 219
- A.2 Drive Specifications 221
- A.3 Drive Watt Loss Data 223
- A.4 Drive Derating Data 224
- Temperature Derating 225
- Altitude Derating 225
- Appendix: B 227
- A1: Initialization 228
- A2: User Parameters 228
- B.2 b: Application 229
- Parameter List 231
- B.3 C: Tuning 234
- C3: Slip Compensation 235
- C4: Torque Compensation 235
- C6: Carrier Frequency 235
- B.4 d: References 236
- B.5 E: Motor Parameters 239
- E2: Motor 1 Parameters 240
- B.6 F: Options 242
- <1> 244
- H4: Analog Outputs 252
- H6: Pulse Train Input 253
- B.8 L: Protection Function 254
- L3: Stall Prevention 255
- L4: Speed Detection 257
- L5: Fault Restart 257
- L6: Torque Detection 258
- L8: Drive Protection 259
- B.11 P: Pump Parameters 265
- P2: Pump Protection 267
- P4: Pump Advanced 268
- P5: Pump HAND Mode 270
- P7: Anti-Jam 271
- P9: Network Options 271
- Q3: Output Current Limit 275
- Q1: Preset Setpoint 275
- B.13 S: Special Application 276
- B.14 T: Motor Tuning 277
- B.15 U: Monitors 278
- U2: Fault Trace 281
- U3: Fault History 281
- U4: Maintenance Monitors 283
- U5: PID Monitors 285
- U6: Operation Status Monitors 285
- U9: Operation Status Monitors 285
- B.16 Defaults by Drive Model 286
- Appendix: C 291
- C.1 UL Standards 292
- Single-Phase 200 V Class 293
- Three-Phase 200 V Class 293
- Three-Phase 400 V Class 294
- Standards Compliance 295
- Drive Short-Circuit Rating 296
- Revision History 298
Produits connexes et manuels pour Équipement Yaskawa iQpump Micro
Équipement Yaskawa 1000 Series Drive Option - CANopen Technical Manua Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Yaskawa 1000 Series Drive Option - CC-Link Technical Manua Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Yaskawa 1000 Series Drive Option - DeviceNet Installation Manuel d'utilisateur
(37 pages)
(37 pages)
Équipement Yaskawa 1000 Series Drive Option - DeviceNet Technical Man Manuel d'utilisateur
(81 pages)
(81 pages)
Équipement Yaskawa 1000 Series Drive Option - MECHATROLINK-II Install Manuel d'utilisateur
(32 pages)
(32 pages)
Équipement Yaskawa 1000 Series Drive Option - Digital Output Installa Manuel d'utilisateur
(31 pages)
(31 pages)
Équipement Yaskawa 1000 Series Drive Option - MECHATROLINK-II Technic Manuel d'utilisateur
(41 pages)
(41 pages)
Équipement Yaskawa 1000 Series Drive Option - Profibus-DP Installatio Manuel d'utilisateur
(35 pages)
(35 pages)
Équipement Yaskawa 1000 Series Drive Option - Open Collector Type PG Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Yaskawa Z1000U Manuel d'utilisateur
(378 pages)
(378 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.220 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels