YASKAWA VS-606V7 Series Manuel d'instructions Page 173
- Page / 218
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
172
Protective
Operation
Output is
turned OFF
and motor
coasts to a
stop.
EF (External fault)
Inverter receives an external
fault input from control circuit
terminal.
EF0: External fault reference
through MEMOBUS
communications
EF1: External fault input
command from control
circuit terminal S1
EF2: External fault input
command from control
circuit terminal S2
EF3: External fault input
command from control
circuit terminal S3
EF4: External fault input
command from control
circuit terminal S4
EF5: External fault input
command from control
circuit terminal S5 *
EF6: External fault input
command from control
circuit terminal S6 *
EF7: External fault input
command from control
circuit terminal S7
Check the following:
• NO/NC contact selection
(constant).
• Wiring is made properly.
• Signal is not input from
the PLC.
CPF-00
Inverter cannot communicate
with the Digital Operator for 5
s or more when power is
turned ON.
Cycle power after confirming
that the Digital Operator is se-
curely mounted. If the fault re-
mains, replace the Digital
Operator or Inverter.
CPF-01
Transmission fault occurred
for 5 s or more when trans-
mission starts with the Digital
Operator.
Cycle power after confirming
that the Digital Operator is se-
curely mounted. If the fault re-
mains, replace the Digital
Operator or Inverter.
CPF-04
EEPROM fault of Inverter
control circuit was detected.
• Record all constant data
and initialize the con-
stants. (Refer to page 50.)
• Cycle power. If the fault
remains, replace the
Inverter.
CPF-05
AD converter fault was de-
tected.
Cycle power.
If the fault remains, replace
the Inverter.
Fault Display Inverter
Status
Description Causes and Corrective
Actions
Digital
Operator
RUN (Green)
ALARM (Red)
- INSTRUCTION MANUAL 1
- General Precautions 2
- PRECAUTIONS FOR CE MARKINGS 4
- RECEIVING THE PRODUCT 5
- MOUNTING 5
- OPERATION 8
- The Inverter may be damaged 10
- MAINTENANCE AND INSPECTION 11
- (Ref. page) 12
- WARNING LABEL 13
- WARRANTY INFORMATION 14
- RESTRICTIONS 15
- CONTENTS 16
- Revision History 20
- 1. Receiving the Product 21
- Checking the Nameplate 22
- 2. Identifying the Parts 23
- Inverter model 25
- 3. Mounting 26
- Mounting Dimensions 27
- Removing the Front Cover 28
- Mounting the Front Cover 28
- Removing the Terminal Cover 28
- Mounting the Terminal Cover 29
- Removing the Digital 29
- Operator 29
- Removing the Bottom Cover 30
- Mounting the Bottom Cover 30
- 4. Wiring 31
- Wiring the Main Circuits 37
- Wiring the Control Circuits 39
- CONTACT OUTPUT 40
- 5. Operating the Inverter 41
- Te st R u n 42
- Operation Check Points 44
- JVOP-140 Digital Operator 45
- FWD/REV run selection 47
- Selecting the Monitor 48
- Monitoring 49
- Input terminal status 50
- Output terminal status 50
- yyyyyy 4-digit number 51
- : Order of fault (1 to 4) 51
- Simple Data Setting 52
- : Flashing : OFF 53
- (Frequency) 56
- V: (Voltage) 56
- Motor Specification: 60 Hz 57
- (Factory setting) 57
- Motor Specification: 50 Hz 57
- Selected: n002=0) 58
- Using Vector Control Mode 59
- Motor Constant Calculation 60
- [Motor Specification: 60 Hz] 61
- [Motor Specification: 50 Hz] 61
- Constant torque 62
- Constant output or 62
- Selecting RUN/STOP Commands 63
- REMOTE Mode 64
- LOCAL Mode 65
- 8-step speed change 66
- Operating at Low Speed 67
- 0 V 10 V 69
- Min. Output Frequency 72
- Motor Current 73
- Multi-function Output Signal 73
- (Overtorque Detection Signal) 73
- Terminal MA, MB, P1, or P2 73
- Frequency Detection 1 75
- Frequency Detection 2 75
- SPEED SEARCH Command 76
- Command Input 78
- Output (n065) 79
- Used as a Sourcing Output 81
- Used as a Sinking Input 81
- Deceleration to a Stop 86
- Coast to a Stop 87
- Using Input Signals 89
- FWD Run When Open 91
- REV Run When Closed 91
- (Setting: 18) 93
- Analog Input Level 95
- Current Reference Selection 99
- 6. Programming Features 100
- Motor Protection 106
- General-purpose Motor 107
- Inverter Motor 107
- Communications specified 109
- Message Format 111
- (Example) 113
- (1: MA ON 0: MA OFF) 115
- (1: P1 ON 0: P1 OFF) 115
- (1: P2 ON 0: P2 OFF) 115
- Data link status 117
- Inverter status 119
- Multi-function 119
- Inverter 119
- Error code 122
- Performing Self-test 123
- Voltage Fluctuation 126
- Output Voltage 126
- Motor Code 128
- Using PID Control Mode 129
- (n130, n131, n132) 132
- PID Offset Adjustment (n133) 132
- PID Output Gain (n163) 133
- PID Feedback Gain (n129) 133
- PID Upper Limit 134
- Prohibition of PID Output 134
- PID Control Block Diagram 135
- Constant Copy Function 137
- READ Function 139
- COPY Function 140
- STOP/RESET 141
- VERIFY Function 142
- Inverter Capacity Display 144
- Software No. Display 146
- Display List 146
- redisplays the constant No 147
- Function is Valid 148
- Loss (n064) 150
- Undertorque Detection 152
- Setting Description 153
- Brake ON/OFF Sequence 154
- Sequence 155
- External Baseblock Signal 157
- Periodic Inspection 159
- Part Replacement 160
- Airflow Direction 161
- Fan Wire 162
- 8. Fault Diagnosis 163
- Alarm Display 164
- Fault Display 168
- OL2 (Inverter overload) 171
- OL3 (Overtorque detec 171
- EF (External fault) 173
- Troubleshooting 176
- 9. Specifications 178
- Grounding 185
- Power Supply 185
- Terminal Descriptions 186
- Transistor 189
- Dimensions/Heat Loss 191
- Constants List 197
- −100% to 205
- • 200 V Class Single-phase 209
- • 400 V Class 3-phase 209
- CE Markings 210
- EMC Directive 211
- Installation Method 211
- EMC Noise Filter 214
- CIMR-V7 215
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance YASKAWA VS-606V7 Series
(41 pages)
(122 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.234 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels