YASKAWA VS-606V7 Series Manuel d'instructions Page 79
- Page / 218
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
78
In factory setting, analog voltage of approx. 10 V is output when output
frequency (output current) is 100 %.
Calibrating Frequency Meter or Ammerter (n067)
Used to adjust analog output gain.
Set the analog output voltage at 100 % of output frequency (output cur-
rent). Frequency meter displays 0 to 60 Hz at 0 to 3 V.
Using Analog Output (AM-AC) as a Pulse Train Signal
Output (n065)
Analog output AM-AC can be used as a pulse train output (output fre-
quency monitor, frequency reference monitor).
Set n065 to 1 when using pulse train output.
Constant No. Name Unit Setting
range
Factory setting
n065 Monitor output type - 0, 1 0
FMAM
AC
100 %
10 V
0
Frequency
Meter
Analog monitor gain
can be set by n067.
Analog Output
Output Frequency
(Output Current)
n067
AM
AC
FM
Frequency Meter/Ammeter
(3 V 1 mA Full-scale)
n067 = 1.00
Factory Setting
n067 = 0.30
100 %
10 V3 V
0
Analog Output
Output Frequency
(Output Current)
10 V ×
n067 setting
0.30
= 3 V
Output frequency becomes
100 % at this value.
- INSTRUCTION MANUAL 1
- General Precautions 2
- PRECAUTIONS FOR CE MARKINGS 4
- RECEIVING THE PRODUCT 5
- MOUNTING 5
- OPERATION 8
- The Inverter may be damaged 10
- MAINTENANCE AND INSPECTION 11
- (Ref. page) 12
- WARNING LABEL 13
- WARRANTY INFORMATION 14
- RESTRICTIONS 15
- CONTENTS 16
- Revision History 20
- 1. Receiving the Product 21
- Checking the Nameplate 22
- 2. Identifying the Parts 23
- Inverter model 25
- 3. Mounting 26
- Mounting Dimensions 27
- Removing the Front Cover 28
- Mounting the Front Cover 28
- Removing the Terminal Cover 28
- Mounting the Terminal Cover 29
- Removing the Digital 29
- Operator 29
- Removing the Bottom Cover 30
- Mounting the Bottom Cover 30
- 4. Wiring 31
- Wiring the Main Circuits 37
- Wiring the Control Circuits 39
- CONTACT OUTPUT 40
- 5. Operating the Inverter 41
- Te st R u n 42
- Operation Check Points 44
- JVOP-140 Digital Operator 45
- FWD/REV run selection 47
- Selecting the Monitor 48
- Monitoring 49
- Input terminal status 50
- Output terminal status 50
- yyyyyy 4-digit number 51
- : Order of fault (1 to 4) 51
- Simple Data Setting 52
- : Flashing : OFF 53
- (Frequency) 56
- V: (Voltage) 56
- Motor Specification: 60 Hz 57
- (Factory setting) 57
- Motor Specification: 50 Hz 57
- Selected: n002=0) 58
- Using Vector Control Mode 59
- Motor Constant Calculation 60
- [Motor Specification: 60 Hz] 61
- [Motor Specification: 50 Hz] 61
- Constant torque 62
- Constant output or 62
- Selecting RUN/STOP Commands 63
- REMOTE Mode 64
- LOCAL Mode 65
- 8-step speed change 66
- Operating at Low Speed 67
- 0 V 10 V 69
- Min. Output Frequency 72
- Motor Current 73
- Multi-function Output Signal 73
- (Overtorque Detection Signal) 73
- Terminal MA, MB, P1, or P2 73
- Frequency Detection 1 75
- Frequency Detection 2 75
- SPEED SEARCH Command 76
- Command Input 78
- Output (n065) 79
- Used as a Sourcing Output 81
- Used as a Sinking Input 81
- Deceleration to a Stop 86
- Coast to a Stop 87
- Using Input Signals 89
- FWD Run When Open 91
- REV Run When Closed 91
- (Setting: 18) 93
- Analog Input Level 95
- Current Reference Selection 99
- 6. Programming Features 100
- Motor Protection 106
- General-purpose Motor 107
- Inverter Motor 107
- Communications specified 109
- Message Format 111
- (Example) 113
- (1: MA ON 0: MA OFF) 115
- (1: P1 ON 0: P1 OFF) 115
- (1: P2 ON 0: P2 OFF) 115
- Data link status 117
- Inverter status 119
- Multi-function 119
- Inverter 119
- Error code 122
- Performing Self-test 123
- Voltage Fluctuation 126
- Output Voltage 126
- Motor Code 128
- Using PID Control Mode 129
- (n130, n131, n132) 132
- PID Offset Adjustment (n133) 132
- PID Output Gain (n163) 133
- PID Feedback Gain (n129) 133
- PID Upper Limit 134
- Prohibition of PID Output 134
- PID Control Block Diagram 135
- Constant Copy Function 137
- READ Function 139
- COPY Function 140
- STOP/RESET 141
- VERIFY Function 142
- Inverter Capacity Display 144
- Software No. Display 146
- Display List 146
- redisplays the constant No 147
- Function is Valid 148
- Loss (n064) 150
- Undertorque Detection 152
- Setting Description 153
- Brake ON/OFF Sequence 154
- Sequence 155
- External Baseblock Signal 157
- Periodic Inspection 159
- Part Replacement 160
- Airflow Direction 161
- Fan Wire 162
- 8. Fault Diagnosis 163
- Alarm Display 164
- Fault Display 168
- OL2 (Inverter overload) 171
- OL3 (Overtorque detec 171
- EF (External fault) 173
- Troubleshooting 176
- 9. Specifications 178
- Grounding 185
- Power Supply 185
- Terminal Descriptions 186
- Transistor 189
- Dimensions/Heat Loss 191
- Constants List 197
- −100% to 205
- • 200 V Class Single-phase 209
- • 400 V Class 3-phase 209
- CE Markings 210
- EMC Directive 211
- Installation Method 211
- EMC Noise Filter 214
- CIMR-V7 215
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance YASKAWA VS-606V7 Series
(41 pages)
(122 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.222 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels