YASKAWA Inverter Spécifications Page 15
- Page / 242
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Receiving
This chapter describes the proper inspections to perform after receiving the drive and illustrates the
different enclosure types and components.
1.1 SECTION SAFETY.................................................................................................16
1.2 MODEL NUMBER AND NAMEPLATE CHECK....................................................17
1.3 COMPONENT NAMES...........................................................................................19
1
YASKAWA ELECTRIC SIEP C710606 31A YASKAWA AC Drive – J1000 Technical Manual
15
- YASKAWA AC Drive-J1000 1
- Table of Contents 3
- Preface & General Safety 9
- Applicable Documentation 10
- Terms and Abbreviations 10
- Drive Label Warnings 13
- Warranty Information 14
- Quick Reference 14
- Receiving 15
- 1.1 Section Safety 16
- Nameplate 17
- Three-Phase 200 V 18
- Three-Phase 400 V 18
- 1.3 Component Names 20
- Mechanical Installation 23
- 2.1 Section Safety 24
- 2.2 Mechanical Installation 26
- IP20/Open-Chassis Drives 29
- Electrical Installation 31
- 3.1 Section Safety 32
- Main circuit 34
- Control circuit 34
- 3.5 Protective Covers 38
- Three-Phase 200 V Class 40
- Three-Phase 400 V Class 40
- Ground Wiring 40
- 3.7 Control Circuit Wiring 42
- Wiring Procedure 44
- DIP Switch S3 46
- 3.8 I/O Connections 47
- 3.9 Main Frequency Reference 48
- 3.10 Braking Resistor 50
- 3.12 Wiring Checklist 52
- 4.1 Section Safety 54
- Start-Up Programming 55
- & Operation 55
- Keys, Displays, and LEDs 56
- PROGRAMMING MODE 58
- DRIVE MODE 58
- Drive Mode Details 60
- Programming Mode Details 60
- 4.4 Start-up Flowchart 64
- No-Load Operation Test Run 66
- Parameter Access Level: A1-01 68
- Copy Function (Optional) 68
- 5.1 A: Initialization 72
- Setting 0: Operator 76
- 5.2 b: Application 80
- 5.3 C: Tuning 81
- C2: S-Curve Characteristics 82
- C3: Slip Compensation 82
- C4: Torque Compensation 83
- C6: Carrier Frequency 83
- 5.4 d: Reference Settings 86
- Operating 88
- 5.5 E: Motor Parameters 90
- E2: Motor 1 Parameters 92
- Setting 14: Fault Reset 97
- Setting 1: Zero Speed 100
- Setting 2: Speed Agree (f 100
- Agree ) 100
- Parameter Details 101
- Frequency 104
- Bias = 0 % 104
- 0 V 10 V 104
- Gain = 100 % 104
- 5.7 L: Protection Functions 107
- <1> 110
- <1> 110
- L4: Speed Agree 111
- L5: Fault Restart 112
- L6: Torque Detection 112
- L8: Hardware Protection 113
- L8-18: Software CLA Selection 114
- 5.8 n: Special Adjustments 116
- This Page Intentionally Blank 122
- Troubleshooting 123
- 6.1 Section Safety 124
- <2> 127
- Minor Faults and Alarms 128
- Operation Errors 128
- 6.4 Fault Detection 130
- 6.5 Alarm Detection 136
- Run Command 140
- 7.1 Section Safety 146
- Periodic Inspection & 147
- Maintenance 147
- 7.2 Inspection 148
- Installing the Cooling Fan 152
- 8.1 Section Safety 154
- Peripheral Devices & 155
- Installing a Leakage Breaker 158
- Connecting a Surge Suppressor 159
- Connecting a Noise Filter 160
- Zero-Phase Reactor 161
- Long Motor Cables 162
- (Figure 8.12, A) 166
- Appendix: A 169
- Specifications 171
- <2> 173
- <3> 173
- <4> 173
- A.4 Drive Specifications 174
- A.6 Drive Derating Data 176
- Appendix: B 177
- B.1 Parameter Groups 178
- <22> 179
- C: Tuning 180
- Parameter List 181
- E: Motor Parameters 182
- <37> 183
- <57> 183
- <18> 184
- <39> 186
- <63> 187
- <7> 187
- <12> 188
- Multi-Function 191
- Digital Output (fault) 191
- (terminal MA/MB-MC) 191
- B.2 Parameter Table 192
- Appendix: C 195
- C.1 Section Safety 196
- Master (PLC or other) 197
- DRIVE DRIVE 197
- MEMOBUS/Modbus 197
- Communications 197
- S– S+ IG R– R+ 199
- RS-485 Interface 200
- RS-422 Interface 200
- Network Termination 201
- H5-01: Drive Slave Address 202
- H5-07: RTS Control Selection 203
- Setting 0: 0.1Hz / 1 204
- Setting 1: o1-03 based 204
- Setting 2: 100% / 30000 204
- Setting 3: 0.1% / 1 204
- C.7 Communications Timing 206
- C.8 Message Format 208
- C.9 Message Examples 210
- Command Data 212
- Broadcast Messages 216
- Issuing an Enter Command 218
- Appendix: D 221
- D.1 Section Safety 222
- Standards Compliance 223
- D.2 European Standards 224
- EMC Filters 227
- Drive Short-Circuit Rating 230
- E2-01 Motor Rated Current 230
- D.4 User Setting Table 232
- Numerics 235
- 08-5-2_YEA 242
Produits connexes et manuels pour Tournevis électriques YASKAWA Inverter
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels