YASKAWA Inverter Spécifications Page 52
- Page / 242
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3.12 Wiring Checklist
No. Item Page
Drive, peripherals, option cards
1 Check drive model number to ensure receipt of correct model. 17
2 Check for correct braking resistors, DC reactors, noise filters, and other peripheral devices. 49
Installation area and physical setup
3 Ensure area surrounding the drive complies with specifications. 26
Power supply voltage, output voltage
4 The voltage from the power supply should fall within the input voltage specification range of the drive. 90
5 The voltage rating for the motor should match the drive output specifications. 17
Main circuit wiring
6 Confirm proper branch circuit protection exists per National and Local codes. 34
7 Properly wire the power supply to drive terminals R/L1, S/L2 and T/L3. 36
8
Properly wire the drive and motor together.
The
motor lines and drive output terminals R/T1, V/T2 and W/T3 should match in order to produce the desired phase
order. If the phase order is incorrect, the drive will rotate in the opposite direction.
40
9 Use 600 Vac vinyl-sheathed wire for the power supply and motor lines. 39
10 Use the correct wire gauges for the main circuit. Refer to Table 3.2, Table 3.3, or Table 3.4. 39
• When using comparatively long motor cable, calculate the amount of voltage drop.
3 x voltage resistance (Ω/km) x cable length (m) x motor rated current (A) x 10
-3
Motor rated voltage (V) x 0.02 ≥
39
• If the cable between the drive and motor exceeds 50 m, adjust the carrier frequency (C6-02) accordingly. 40
11 Properly ground the drive. Review page 40. 40
12
Tightly fasten all terminal screws (control circuit terminals, grounding terminals).
Refer to Table 3.2, Table 3.3, or Table 3.4.
39
13
Set up overload protection circuits when running multiple motors from a single drive.
M1
OL1
OL2
OLn
MC1
MC2
MCn
M2
Mn
Drive
MC1 - MCn
OL
1 - OL n
... magnetic contactor
... thermal relay
Power supply
Note: Close MC1 through MCn before operating the drive.
-
14
If using a braking resistor or dynamic braking resistor unit, install a magnetic contactor. Properly install the resistor,
and ensure that overload protection shuts off the power supply.
49
15 Verify phase advancing capacitors are NOT installed on the output side of the drive. -
Control circuit wiring
16 Use twisted-pair cables for all drive control circuit wiring. 42
17 Ground the shields of shielded wiring to the GND terminal. 44
18
If using a 3-Wire sequence, properly set parameters for multi-function contact input terminals S1 through S5, and
properly wire control circuits.
35
19
Check for any other wiring mistakes.
Only use a multimeter to check wiring.
-
20
Properly fasten the control circuit terminal screws in the drive.
Refer to Table 3.2, Table 3.3, or Table 3.4.
39
21 Pick up all wire clippings. -
22 Ensure that no frayed wires on the terminal block are touching other terminals or connections. -
23 Properly separate control circuit wiring and main circuit wiring. -
24 Analog signal line wiring should not exceed 50 m. -
3.12 Wiring Checklist
52
YASKAWA ELECTRIC SIEP C710606 31A YASKAWA AC Drive – J1000 Technical Manual
- YASKAWA AC Drive-J1000 1
- Table of Contents 3
- Preface & General Safety 9
- Applicable Documentation 10
- Terms and Abbreviations 10
- Drive Label Warnings 13
- Warranty Information 14
- Quick Reference 14
- Receiving 15
- 1.1 Section Safety 16
- Nameplate 17
- Three-Phase 200 V 18
- Three-Phase 400 V 18
- 1.3 Component Names 20
- Mechanical Installation 23
- 2.1 Section Safety 24
- 2.2 Mechanical Installation 26
- IP20/Open-Chassis Drives 29
- Electrical Installation 31
- 3.1 Section Safety 32
- Main circuit 34
- Control circuit 34
- 3.5 Protective Covers 38
- Three-Phase 200 V Class 40
- Three-Phase 400 V Class 40
- Ground Wiring 40
- 3.7 Control Circuit Wiring 42
- Wiring Procedure 44
- DIP Switch S3 46
- 3.8 I/O Connections 47
- 3.9 Main Frequency Reference 48
- 3.10 Braking Resistor 50
- 3.12 Wiring Checklist 52
- 4.1 Section Safety 54
- Start-Up Programming 55
- & Operation 55
- Keys, Displays, and LEDs 56
- PROGRAMMING MODE 58
- DRIVE MODE 58
- Drive Mode Details 60
- Programming Mode Details 60
- 4.4 Start-up Flowchart 64
- No-Load Operation Test Run 66
- Parameter Access Level: A1-01 68
- Copy Function (Optional) 68
- 5.1 A: Initialization 72
- Setting 0: Operator 76
- 5.2 b: Application 80
- 5.3 C: Tuning 81
- C2: S-Curve Characteristics 82
- C3: Slip Compensation 82
- C4: Torque Compensation 83
- C6: Carrier Frequency 83
- 5.4 d: Reference Settings 86
- Operating 88
- 5.5 E: Motor Parameters 90
- E2: Motor 1 Parameters 92
- Setting 14: Fault Reset 97
- Setting 1: Zero Speed 100
- Setting 2: Speed Agree (f 100
- Agree ) 100
- Parameter Details 101
- Frequency 104
- Bias = 0 % 104
- 0 V 10 V 104
- Gain = 100 % 104
- 5.7 L: Protection Functions 107
- <1> 110
- <1> 110
- L4: Speed Agree 111
- L5: Fault Restart 112
- L6: Torque Detection 112
- L8: Hardware Protection 113
- L8-18: Software CLA Selection 114
- 5.8 n: Special Adjustments 116
- This Page Intentionally Blank 122
- Troubleshooting 123
- 6.1 Section Safety 124
- <2> 127
- Minor Faults and Alarms 128
- Operation Errors 128
- 6.4 Fault Detection 130
- 6.5 Alarm Detection 136
- Run Command 140
- 7.1 Section Safety 146
- Periodic Inspection & 147
- Maintenance 147
- 7.2 Inspection 148
- Installing the Cooling Fan 152
- 8.1 Section Safety 154
- Peripheral Devices & 155
- Installing a Leakage Breaker 158
- Connecting a Surge Suppressor 159
- Connecting a Noise Filter 160
- Zero-Phase Reactor 161
- Long Motor Cables 162
- (Figure 8.12, A) 166
- Appendix: A 169
- Specifications 171
- <2> 173
- <3> 173
- <4> 173
- A.4 Drive Specifications 174
- A.6 Drive Derating Data 176
- Appendix: B 177
- B.1 Parameter Groups 178
- <22> 179
- C: Tuning 180
- Parameter List 181
- E: Motor Parameters 182
- <37> 183
- <57> 183
- <18> 184
- <39> 186
- <63> 187
- <7> 187
- <12> 188
- Multi-Function 191
- Digital Output (fault) 191
- (terminal MA/MB-MC) 191
- B.2 Parameter Table 192
- Appendix: C 195
- C.1 Section Safety 196
- Master (PLC or other) 197
- DRIVE DRIVE 197
- MEMOBUS/Modbus 197
- Communications 197
- S– S+ IG R– R+ 199
- RS-485 Interface 200
- RS-422 Interface 200
- Network Termination 201
- H5-01: Drive Slave Address 202
- H5-07: RTS Control Selection 203
- Setting 0: 0.1Hz / 1 204
- Setting 1: o1-03 based 204
- Setting 2: 100% / 30000 204
- Setting 3: 0.1% / 1 204
- C.7 Communications Timing 206
- C.8 Message Format 208
- C.9 Message Examples 210
- Command Data 212
- Broadcast Messages 216
- Issuing an Enter Command 218
- Appendix: D 221
- D.1 Section Safety 222
- Standards Compliance 223
- D.2 European Standards 224
- EMC Filters 227
- Drive Short-Circuit Rating 230
- E2-01 Motor Rated Current 230
- D.4 User Setting Table 232
- Numerics 235
- 08-5-2_YEA 242
Produits connexes et manuels pour Tournevis électriques YASKAWA Inverter
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.639 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels