Yaskawa iQpump Micro Manuel d'utilisateur télécharger pdf (Page 119)

4.8 Detailed iQpump Parameter Descriptions

This section explains the basic settings required for initial drive operation. Checking these basic parameter settings will help

to ensure a successful drive start-up. Refer to Parameter List on page 227 for a complete listing of drive parameters if more

information is required for parameters not listed in this section.

Parameter Name Page

A1-01 Access Level Selection 119

A1-03 Initialize Parameters 120

b1-01 Frequency Reference Selection 1 121

b1-02 Run Command Selection 1 124

b1-03 Stopping Method Selection 125

b3-01 Speed Search Selection at Start 127

b5-01 PID Function Setting 127

b5-03 Integral Time Setting (I) 128

b5-09 PID Output Level Selection 128

b5-39 PID Setpoint Display Digits 128

C1-01 to

C1-04

Accel, Decel Times 1 and 2 128

E2-01 Motor Rated Current 129

E2-04 Number of Motor Poles 129

H1-01 to

H1-07

Functions for Terminals S1 to S7 129

H2-01 to

H2-03

Terminal MA/MB/MC, P1/PC, and P2/PC

Function Selection

140

H3-01 Terminal A1 Signal Level Selection 149

H3-02 Terminal A1 Function Selection 149

H3-03,

H3-04

Terminal A1 Gain and Bias Settings 149

H3-09 Terminal A2 Signal Level Selection 150

H3-10 Terminal A2 Function Selection 150

H3-11,

H3-12

Terminal A2 Gain and Bias Setting 150

H4-01

Multi-Function Analog Terminal AM Monitor

Selection

151

H4-02,

H4-03

Multi-Function Analog Output Terminal AM

Gain/Bias

151

L5-01 Number of Auto Restart Attempts 151

L5-04 Fault Reset Interval Time 152

o1-08 Third Line User Monitor Selection 152

P1-01 Pump Mode 152

Parameter Name Page

P1-02 System Units 152

P1-03 Feedback Device Scaling 153

P1-04 Start / Draw Down Level 153

P1-05 Start Level Delay Time 153

P1-06 Minimum Pump Speed 153

P1-08 Low Feedback Level 153

P1-09 Low Feedback Level Fault Delay Time 153

P1-10 Low Feedback Selection 154

P1-11 High Feedback Level 154

P1-12 High Feedback Level Fault Delay Time 154

P1-13 High Feedback Selection 154

P2-01 Sleep Level Type 155

P2-02 Sleep Level 155

P2-03 Sleep Delay Time 155

P4-01 Pre-Charge Level 155

P4-02 Pre-Charge Frequency 155

P4-03 Pre-Charge Time 156

P4-05 Pre-Charge Loss of Prime Level 159

P4-06 Pre-Charge Frequency 2 159

P4-07 Pre-Charge Time 2 159

P4-08 Pre-Charge Loss of Prime Level 2 159

P4-10

AUTO Mode Operator Run Power Down

Storage

159

P4-11 Thrust Bearing Acceleration Time 159

P4-12 Thrust Bearing Frequency 159

P4-13 Thrust Bearing Deceleration Time 160

P4-17 Utility Start Delay 160

P4-32 Pre-Charge Level 2 160

P5-02 HAND Reference 1 161

P5-04 HAND Key Function Selection 161

Q1-01 PID Controller Setpoint 1 161

A1-01: Access Level Selection

Allows or restricts access to drive parameters.

No. Parameter Name Setting Range Default

A1-01 Access Level Selection 0 to 3 2

Setting 0: Operation only

Access to only parameters A1-01, A1-04, and all U monitor parameters.

Setting 1: User Parameters

Access to only a specific list of parameters set to A2-01 through A2-32. These User Parameters can be accessed using the

Setup Mode of the digital operator.

Setting 2: Advanced Access Level (A) and Setup Access Level (S)

All parameters can be viewed and edited.

4.8 Detailed iQpump Parameter Descriptions

YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual

119

Start-Up Programming

& Operation

1 2 ... 114 115 116 117 118 119 120 121 122 123 124 ... 299 300

Commentaires sur ces manuels

Pas de commentaire

Yaskawa iQpump Micro Manuel d'utilisateur Page 119

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa iQpump Micro