Yaskawa iQpump Micro Manuel d'utilisateur télécharger pdf (Page 252)

H4: Analog Outputs

No.

(Addr.

Hex)

Name LCD Display Description Values Page

H4-01

(041D)

Multi-Function Analog

Output Terminal AM

Monitor Selection

Term AM FuncSel

Selects the data to be output through multi-function analog

output terminal AM.

Set the desired monitor parameter to the digits available in

Uo-oo.

For example, enter “103” for U1-03.

Default: 102

Range: 000 to

999

151

H4-02

(041E)

Multi-Function Analog

Output Terminal AM

Gain

Terminal AM Gain

Sets the signal level at terminal AM that is equal to 100% of the

selected monitor value.

Default: 100.0%

Min.: -999.9

Max.: 999.9

151

H4-03

(041F)

Multi-Function Analog

Output Terminal AM

Bias

Terminal AM Bias

Sets the signal level at terminal AM that is equal to 0% of the

selected monitor value.

Default: 0.0%

Min.: -999.9

Max.: 999.9

151

H5: MEMOBUS/Modbus Serial Communication

No.

(Addr.

Hex)

Name LCD Display Description Values Page

H5-01

(0425)

<1>

Drive Node Address Serial Comm Adr

Selects drive station node number (address) for MEMOBUS/

Modbus terminals R+, R-, S+, S-. Cycle power for the setting

to take effect.

Default: 1F

(Hex)

Min.: 0

Max.: FF

<2>

–

H5-02

(0426)

Communication Speed

Selection

Serial Baud Rate

0: 1200 bps

1: 2400 bps

2: 4800 bps

3: 9600 bps

4: 19.2 kbps

5: 38.4 kbps

6: 57.6 kbps

7: 76.8 kbps

8: 115.2 kbps

0: 1200 bps

1: 2400 bps

2: 4800 bps

3: 9600 bps

4: 19200 bps

5: 38400 bps

6: 57600 bps

7: 76800 bps

8: 115200 bps

Cycle power for the setting to take effect.

Default: 3

Range: 0 to 8

–

H5-03

(0427)

Communication Parity

Selection

Serial Com Sel

0: No parity

1: Even parity

2: Odd parity

0: No parity

1: Even parity

2: Odd parity

Cycle power for the setting to take effect.

Default: 0

Range: 0 to 2

–

H5-04

(0428)

Stopping Method after

Communication Error

(CE)

Serial Fault Sel

0: Ramp to Stop

1: Coast to Stop

2: Fast-Stop

3: Alarm Only

0: Ramp to stop

1: Coast to stop

2: Fast Stop

3: Alarm only

Default: 3

Range: 0 to 3

–

H5-05

(0429)

Communication Fault

Detection Selection

Serial Flt Dtct

0: Disabled

1: Enabled

0: Disabled

1: Enabled. If communication is lost for more than two seconds,

a CE fault will occur.

Default: 1

Range: 0, 1

–

H5-06

(042A)

Drive Transmit Wait

Time

Transmit WaitTIM

Set the wait time between receiving and sending data. Default: 5 ms

Min.: 5

Max.: 65

–

H5-07

(042B)

RTS Control Selection

RTS Control Sel

0: Disabled

1: Enabled

0: Disabled. RTS is always on.

1: Enabled. RTS turns on only when sending.

Default: 1

Range: 0, 1

–

H5-09

(0435)

CE Detection Time CE Detect Time

Sets the time required to detect a communications error.

Adjustment may be needed when networking several drives.

Default: 2.0 s

Min.: 0.0

Max.: 10.0

–

H5-10

(0436)

Unit Selection for

MEMOBUS/Modbus

CommReg 25h Unit

0: 0.1 V

1: 1 V

0: 0.1 V units

1: 1 V units

Default: 0

Range: 0, 1

–

H5-11

(043C)

Communications

ENTER Function

Selection

Enter CommandSel

0: Enter Required

1: No EnterRequired

0: Drive requires an Enter command before accepting any

changes to parameter settings.

1: Parameter changes are activated immediately without the

Enter command.

Default: 0

Range: 0, 1

–

B.7 H Parameters: Multi-Function Terminals

252

YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual

1 2 ... 247 248 249 250 251 252 253 254 255 256 257 ... 299 300

Commentaires sur ces manuels

Pas de commentaire

Yaskawa iQpump Micro Manuel d'utilisateur Page 252

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa iQpump Micro