Yaskawa iQpump Micro Manuel d'utilisateur télécharger pdf (Page 251)

No.

(Addr.

Hex)

Name LCD Display Description Values Page

H3-04

(0412)

Terminal A1 Bias

Setting

Terminal A1 Bias

Sets the level of the input value selected in H3-02 when 0 V is

input at terminal A1.

Default: 0.0%

Min.: -999.9

Max.: 999.9

149

H3-09

(0417)

Terminal A2 Signal

Level Selection

Term A2 Level

0: 0-10V,

(LowLim=0)

1: 0-10V, (BipolRef)

2: 4-20 mA

3: 0-20 mA

0: 0 to 10 V

1: -10 to 10 V

2: 4 to 20 mA

3: 0 to 20 mA

Note: Use DIP Switch S1-2 to set input terminal A2 for

a current or voltage input signal.

Default: 2

Range: 0 to 3

150

H3-10

(0418)

Terminal A2 Function

Selection

Term A2 FuncSel

Sets the function of terminal A2. Default: B

Range: 0 to 41

150

H3-11

(0419)

Terminal A2 Gain

Setting

Terminal A2 Gain

Sets the level of the input value selected in H3-10 when 10 V

(20 mA) is input at terminal A2.

Default: 100.0%

Min.: -999.9

Max.: 999.9

150

H3-12

(041A)

Terminal A2 Bias

Setting

Terminal A2 Bias

Sets the level of the input value selected in H3-10 when 0 V (0

or 4 mA) is input at terminal A2.

Default: 0.0%

Min.: -999.9

Max.: 999.9

150

H3-13

(041B)

Analog Input Filter

Time Constant

A1/A2 Filter T

Sets a primary delay filter time constant for terminals A1 and

A2. Used for noise filtering.

Default: 0.03 s

Min.: 0.00

Max.: 2.00

–

H3-14

(041C)

Analog Input Terminal

Enable Selection

A1/A2 Sel

1: A1 Available

2: A2 Available

7: All Available

Determines which analog input terminals will be enabled when

a digital input programmed for “Analog input enable”

(H1-oo = C) is activated.

1: Terminal A1 only

2: Terminal A2 only

7: All terminals enabled

Default: 7

Range: 1, 2, 7

–

H3-16

(0440)

Terminal A1 Offset Term A1 Offset

Adds an offset when the analog signal to terminal A1 is at 0 V. Default: 0

Min.: -500

Max.: 500

–

H3-17

(0441)

Terminal A2 Offset Term A2 Offset

Adds an offset when the analog signal to terminal A2 is at 0 V. Default: 0

Min.: -500

Max.: 500

–

H3 Multi-Function Analog Input Settings

H3-oo

Setting

Function LCD Display Description Page

0 Frequency bias Freq Ref Bias 10 V = E1-04 (maximum output frequency) –

1 Frequency gain Freq Ref Gain

0 to 10 V signal allows a setting of 0 to 100%. -10 to 0 V signal allows a setting

of -100 to 0%.

–

Auxiliary frequency

reference 1

Aux Reference1

10 V = E1-04 (maximum output frequency)

–

4 Output voltage bias Voltage Bias 10 V = E1-05 (motor rated voltage) –

Overtorque/

undertorque

detection level

Torque Det Level

10 V = Drive rated current (V/f)

–

B PID feedback PID Feedback1 10 V = 100% –

C PID setpoint PID Set Point 10 V = 100% –

Motor Temperature

(PTC Input)

E Motor PTC 10 V = 100% –

F Through mode Not Used

Select this setting when using the terminal in a pass-through mode. The terminal

does not trigger a drive function but can be used as digital input for the controller

the drive is connected to.

–

Differential PID

feedback

PID Feedback 2

10 V = 100%

–

1F Through mode Not Used Set this value when using the terminal in the pass-through mode. –

HAND Frequency

Reference

Hand Freq. Ref. Full scale: Max. frequency (E1-04) –

41 Output Voltage Gain V/f out gain 10 V = 100% –

B.7 H Parameters: Multi-Function Terminals

YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual

251

Parameter List

1 2 ... 246 247 248 249 250 251 252 253 254 255 256 ... 299 300

Commentaires sur ces manuels

Pas de commentaire

Yaskawa iQpump Micro Manuel d'utilisateur Page 251

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa iQpump Micro