Yaskawa iQpump Micro Manuel d'utilisateur télécharger pdf (Page 274)

No.

(Addr.

Hex)

Name LCD Display Description Values Page

P9-26

(0E0D)

Master Time-out Master Time-out

Sets the minimum amount of time that the slave drives will wait

for a message from the master before performing the action set

in P9-27.

Default: 4.0 s

Min.: 1.0

Max.: 10.0

–

P9-27

(0E0E)

Network Recovery

0: Automatic

1: Slave/Resume

2: Slave/Stop

3: Fault MSL

Determines the drive response when no messages are received

from the master for the time set in P9-26.

0: Automatic. The drive will attempt to assume master

functionality.

1: Slave/Resume. The drive will continue running when the

master is lost and will wait for a master to come online.

2: Slave/Stop. The drive will stop running when the master is

lost and will wait for a master to come online.

3: Fault MSL. Fault the drive with an MSL (Master Lost).

Default: 0

Range: 0 to 3

–

P9-28

(0E0F)

NETSCAN Alarm Time NETSCAN AlrmTime

Sets the amount of time that the slave drives will wait for a

message from the master before displaying a NETSCAN alarm.

Default: 2.0 s

Min.: 1.0

Max.: 10.0

–

P9-29

(0E10)

Net Start Delay Net Start Delay

Sets the amount of time that the network will wait before

selecting and starting the lead drive after the first drive on the

network has been put on AUTO Mode.

Default: 2.0 s

Min.: 0.0

Max.: 60.0

–

P9-30

(0E11)

Lag Drive Speed

Follower Gain

Lag Followr Gain

Sets the gain to be applied to the speed of the current lead drive

when P9-05 is set to 3. The bias to be applied is set in P9-31.

Default: 100.0%

Min.: 0.0

Max.: 300.0

–

P9-31

(0E12)

Lag Drive Speed

Follower Bias

Lag Followr Bias

Sets the bias to be applied to the speed of the current lead drive

when P9-05 is set to 3. The gain to be applied is set in P9-30.

Default: 0.00 Hz

Min.: -60.0

Max.: 60.0

–

P9-32

(0E13)

Lag Follower

Deceleration Time

Lag Followr Dcel

Sets the deceleration time when the P9-33 timer is running and

the drive is running as Lag Drive Speed Follower (P9-05 is set

to 3).

Default: 60.0 s

Min.: 0.0

Max.: 1000.0

–

P9-33

(0E14)

Lag Follower

Deceleration Time

Active Time

Lag Followr Dtim

Sets the time during which the deceleration time set in P9-32 is

effective. The drive will use the standard deceleration rate when

it expires.

Setting this parameter to 0.0 disables the function.

Default: 0.0 s

Min.: 0.0

Max.: 3600.0

–

P9-34

(0E15)

Low Feedback Quick

De-Stage

Low FB De-stage

Sets the low feedback level that will trigger a quick de-stage.

The quick de-stage ignores parameters P9-12 and P9-15 and

only uses an internal 2 second delay.

Setting this parameter to 0.0 disables the function.

Default: 0.0 PSI

<1>

Min.: 0.0

Max.: 6000.0

–

P9-99

(0E56)

Network Compatibility

Selection

Network Comp Sel

0: A-Ver: 30034

1: B-Ver: 30035/36

2: iQ SmartNetwork

Determines the communication compatibility for the iQPump

MEMOBUS network.

0: A-Ver: 30034

1: B-Ver: 30035/36

2: iQ SmartNetwork

Default: 2

Range: 0 to 2

–

<1> Unit is determined by P1-02, System Units; scaling is determined by P1-03, Feedback Device Scaling; resolution is determined by b5-39, PID

System Units Display Digits.

B.11 P: Pump Parameters

274

YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual

1 2 ... 269 270 271 272 273 274 275 276 277 278 279 ... 299 300

Commentaires sur ces manuels

Pas de commentaire

Yaskawa iQpump Micro Manuel d'utilisateur Page 274

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Yaskawa iQpump Micro