YASKAWA SERVO Manuel d'utilisateur Page 185
- Page / 239
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9.2 Warning Displays
9-13
9
Troubleshooting
Note 1. Set Pn001.3 =1 (Outputs both Alarm Codes and Warning Codes) to output warning codes.
2. If Pn008.2 = 1 (Does not detect warning) is selected, warnings other than the undervoltage warning (A.971) will
not be detected.
A.94A
Command Option Module IF
Data Setting Warning 1
This warning occurs when there is an error in a
parameter number sent to the SERVOPACK from
the host controller or command option module.
OFF
(open)
OFF
(open)
ON
(close)
A.94B
Command Option Module IF
Data Setting Warning 2
This warning occurs when out-of-range data is sent
to the SERVOPACK from the host controller or
command option module.
A.94C
Command Option Module IF
Data Setting Warning 3
This warning occurs when there is an error in the
parameter data sent to the SERVOPACK from the
host controller or command option module.
A.94D
Command Option Module IF
Data Setting Warning 4
This warning occurs when there is an error in the
data size sent to the SERVOPACK from the host
controller or command option module.
A.94E
Command Option Module IF
Data Setting Warning 5
This warning occurs when there is an error in the
latch mode settings sent to the SERVOPACK from
the host controller or command option module.
A.95A
Command Option Module IF
Command Warning 1
This warning occurs when the host controller or
command option module outputs an operating
command when the operation execution conditions
in the SERVOPACK have not been met.
ON
(close)
OFF
(open)
ON
(close)
A.95B
Command Option Module IF
Command Warning 2
This warning occurs when there is an error in the
command output from the command option mod-
ule to the SERVOPACK.
A.95D
Command Option Module IF
Command Warning 4
This warning occurs when a latch command is out-
put from the command option module to the SER-
VOPACK during latch operation.
A.95E
Command Option Module IF
Command Warning 5
This warning occurs when an unallowed command
combination is output to the SERVOPACK from
the command option module.
A.95F
Command Option Module IF
Command Warning 6
This warning occurs when there is an error in the
command output to the SERVOPACK from the
command option module.
A.960
Command Option Module IF
Communications Warning
This warning occurs when an error occurred in
communications between the SERVOPACK and
command option module.
OFF
(open)
ON
(close)
ON
(close)
A.971 Undervoltage
This warning occurs before the undervoltage alarm
(A.410) occurs. If the warning is ignored and oper-
ation continues, an undervoltage alarm may occur.
ON
(close)
ON
(close)
ON
(close)
A.
A9F Error
Some kind of
error has occurred at the INDEXER
Module.
Refer to 9.2.2 INDEXER Module Error Displays
and Troubleshooting.
ON
(close)
OFF
(open)
OFF
(open)
(cont’d)
Warning
Display
Warning Name Meaning
Warning Code Output
/ALO1 /ALO2 /ALO3
- Σ-V Series 1
- About this Manual 3
- Pn000㧩㨚㧜㧜㧜㧜 4
- PROHIBITED 5
- MANDATORY 5
- Safety Precautions 6
- WARNING 6
- CAUTION 10
- Warranty 11
- (3) Suitability for Use 12
- (4) Specifications Change 12
- Applicable Standards 13
- Contents 14
- Revision History 17
- Overview 18
- 1 Overview 19
- SGDV – OC A03 A 20
- Nameplate (Ratings) 21
- Nameplate (Model no.) 21
- Specifications 22
- 2.1.1 Main Functions 23
- 2.2 General Specifications 25
- 2.4 LED Indicators 27
- SERVOPACK Installation 28
- Standards 29
- 3.2 SERVOPACK Installation 30
- 3.2.2 Installation Standards 31
- Single-phase 100 V 32
- Three-phase 200 V 33
- Three-phase 400 V 37
- Wiring and Connection 39
- SGDV-FE1A 40
- SERVOPACK 40
- INDEXER Module 40
- SGMJV/SGMAV/SGMPS/SGMCS 40
- Servomotor 40
- Personal computer 41
- (SIEP S800000 60) 42
- (when an absolute 43
- SGDV-FE5A 44
- S800000 66) 46
- SGDV-DE5A 47
- 4.2 I/O Signal Connections 48
- (2) Output Signals 49
- (3) CN11 Input Signals 49
- 4 Wiring and Connection 50
- 4.2.2 Interface Circuits 52
- SGDV SERVOPACK 54
- RS-422 or RS-485 56
- Host controller 56
- 4.3.3 Connector Signal Names 57
- 4.3.4 Connection Examples 58
- 4.3.5 RS-422/RS-485 Interface 59
- 5.1 Parameter Configurations 62
- 5.3.1 Servo ON Signal (/S-ON) 65
- 5.3.2 Overtravel 65
- Overtravel 66
- After stoppingStopping Method 66
- (/ALO1, /ALO2, and /ALO3) 67
- Emergency stop 68
- 5 to 24 VDC 68
- Photocoupler 68
- 5.3 Sequence I/O Signals 69
- Reference speed 70
- Motor speed 70
- Position error 70
- /INPOSITION 70
- (1) Signal Specifications 71
- (2) Related Parameters 71
- 5.3.9 Encoder Signal Outputs 72
- 5.4.1 Setting Reference Units 73
- Position References 74
- Forward Software Limit 76
- (P-LS): PnB21 76
- Reverse Software Limit 76
- (N-LS): PnB23 76
- Workpiece 76
- 5.4.3 Setting Home Position 78
- 5.4.4 Backlash Compensation 79
- 5.4.5 Torque Limit 79
- 6.1 Program Table 82
- 6.1.4 Program Table Settings 85
- 6.1.6 Program Table Operation 89
- (2) Resetting the Program 90
- 6.1.10 Program Table Examples 93
- (4) Using ZONE Table 95
- Zone Table 96
- (6) Using INFINITE 97
- (7) Using Registration 97
- Continuous Stop Function 98
- Latch operation 99
- 6.2.3 Registration Operation 100
- Program Table 101
- 6.3 ZONE Table Settings 102
- ZONEN = +11000 ZONEP = +1000 103
- 6.4 Homing/JOG Speed Table 104
- 6 Program Table 106
- 6.6 JOG Speed Table Operation 108
- 6.6.2 JOG Speed Table 109
- Operation 110
- Serial Command Communications 111
- 7.2 Settings 113
- 7.3 Command/Response Format 114
- 7.5 Echoback Response Time 116
- 7.6.1 Positive Responses 117
- 7.6.2 Negative Responses 117
- 7.7 Serial Commands 118
- 7.7.2 Control Commands 119
- 1 t2 t3 t4 120
- 7.7.2 Control Commands 122
- 1+y2 = y) 129
- 7.7.3 Parameter Edit Commands 132
- Operation of Digital Operator 146
- 8.1 Overview 147
- 㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙 148
- 㧼㧻㧿㧜㧜㧜㧩㧵㧗㧝㧞㧟㧠㧡㧢㧣㧤 148
- 㧼㧻㧿㧜㧜㧝㧩㧭㧗㧝㧞㧟㧠㧡㧢㧣㧤 148
- 㧼㧻㧿㧜㧜㧞㧩㧗㧵㧺㧲㧵㧺㧵㨀㧱 148
- 㧼㧻㧿㧜㧜㧟㧩㧿㨀㧻㧼 148
- 8.2.1 Utility Functions 149
- (1) Preparation 151
- (2) Editing Program Table 151
- 㧭㧯㧯㧜㧜㧞㧩㧦 152
- 㧭㧯㧯㧜㧜㧟㧩㧦 152
- 㧭㧯㧯㧜㧜㧠㧩㧦 152
- 㧭㧯㧯㧜㧜㧡㧩㧜㧜㧜㧜㧝㧜㧜㧜 152
- POS: Target Position 153
- SPD: Positioning Speed 153
- RSPD: Registration Speed 153
- ACC: Acceleration 154
- DEC: Deceleration 154
- EVENT: Pass Condition 154
- (4) Saving Program Tables 155
- (3) Saving ZONE Tables 157
- (2) Editing JOG Speed Tables 159
- (2) Operating Procedure 161
- 㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙 165
- 㧲㨚㧮㧜㧤ޓ㧶㧿㧼㧰ޓ㧵㨚㨕㨠 165
- 㧲㨚㧮㧜㧥ޓ㨆㧿㧱㨀 165
- 㧲㨚㧮㧜㧭ޓ㧹㨛㨚㨕㨠㨛㨞 165
- 㧲㨚㧮㧜㧮ޓ㧼㨞㨙ޓ㧵㨚㨕㨠 165
- 㧲㨚㧮㧜㧯ޓ㧭㧸㧹ޓ㧾㨑㨟㨑㨠 171
- 㧲㨚㧮㧜㧰ޓ㧵㨚㨐㨑㨤㨑㨞ޓ㧭㧸㧹 171
- 㧲㨚㧜㧜㧜ޓ㧭㨘㨙ޓ㧴㨕㨟㨠㨛㨞㨥 171
- Troubleshooting 173
- 9.1 Troubleshooting 174
- 9 Troubleshooting 176
- 9.2 Warning Displays 184
- Status Displays 186
- (2) Linear Servomotors 196
- (cont’d) 198
- Appendix 202
- 10 Appendix 203
- SERVOPACKs 210
- 10.3 Monitor Modes 227
- Revision number 238
- WEB revision number 238
Produits connexes et manuels pour Tournevis électriques YASKAWA SERVO
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.837 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels