Yaskawa iQpump Controller Programming Manual Manuel d'utilisateur Page 289
- Page / 302
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
YASKAWA TM.iQp.07 iQpump Controller Programming Manual 289
P9-04
<0034>
0883
Alternation Mode
Alternation Mode
Determines how alternation is performed:
0: FIFO Auto
1: FIFO Forced
2: LIFO
0 ~ 2 0 Programming
P9-05
<0034>
0884
Lag Drive Mode
Lag Drive Mode
Determines how the lag drives function.
0: Fixed Speed - Runs at the P9-06 setting.
1: PI Regulation - Uses PI to determine speed.
0 ~ 1 0 Programming
P9-06
<0034>
0885
Lag Fixed Speed
Lag Fixed Speed
When the drive changes from a lead to a lag and P9-05 = 0, the drive
will run at this speed after P9-07 delay time expires.
0.0 ~
120.0 Hz
55.0 Hz Programming
P9-07
<0034>
0886
Lag Fixed Speed Delay
Lag Fixed Spd Dly
When the drive changes from a lead to a lag and P9-05 = 0, this time
specifies how long before the drive runs at the P9-06 speed.
0 ~ 1000 s 5 s Programming
P9-08
<0034>
0887
Add Pump Mode
Add Pump Mode
Selects the detection method for staging a new pump:
0: Output Frequency
1: Feedback
2: Feedback + Fout
0 ~ 2 0 Programming
P9-09
<0034>
0888
Add Freq Level
Add Freq Lvl
When P9-08 = 0 and the output frequency rises above this level for the
time set in P9-11, the lead drive will request for a new lead drive
through the iQpump Memobus Network.
When P9-08 = 2 and the output frequency rises above this level the
delta feedback (setpoint - feedback) has exceeded the level set in
P9-10 for the time set in P9-11, the lead drive will request for a new
lead drive through the iQpump Memobus network.
0.0 ~
120.0 Hz
56.0 Hz Programming
P9-10
<0034>
0889
Add Delta Level
Add Delta Lvl
When P9-08 = 1 and the delta feedback (setpoint - feedback) has
exceeded this level for the time set in P9-11, the lead drive will request
for a new lead drive through the iQpump Memobus Network.
When P9-08 = 2 and the delta feedback (setpoint - feedback) has
exceeded this level and the output frequency is above P9-09 for the
time set in P9-11, the lead drive will request for a new lead drive
through the iQpump Memobus network.
0 ~ 6000.0
(system
units
P1-02)
0.0
(system
units
P1-02)
Programming
P9-11
<0034>
088A
Add Delay Time
Add Dly Time
Delay time before a new lead drive is added to the system. 0 ~ 3600 s 10 s Programming
P9-12
<0034>
088B
Remove Pump Mode
Remove Pump Mode
Selects the detection method for de-staging to the previous lead pump:
0: Output Frequency
1: Feedback
2: Feedback + Fout
0 ~ 2 0 Programming
P9-13
<0034>
088C
Remove Freq Level
Remove Freq Lvl
When P9-12 = 0 and the output frequency drops below this level for
the time set in P9-15, the lead drive will request to be removed from
the system through the iQpump Memobus network.
When P9-12 = 2 and the output frequency drops below this level and
the delta feedback (feedback - setpoint) has exceeded the level set in
P9-14 for the time set in P9-15, the lead drive will request to be
removed from the system through the iQpump Memobus network.
0.0 ~
120.0 Hz
40.0 Hz Programming
P9-14
<0034><003
4>
088D
Remove Delta Level
Remove Delta Lvl
When P9-12 = 1 and the delta feedback (feedback - setpoint) has
exceeded this level for the time set in P9-15, the lead drive will request
to be removed from the system through the iQpump Memobus
network.
When P9-12 = 2 and the delta feedback (feedback - setpoint) has
exceeded this level and the output frequency is below P9-13 for the
time set in P9-15, the lead drive will request to be removed from the
system through the iQpump Memobus network.
0 ~ 6000.0
(system
units
P1-02)
0.0
(system
units
P1-02)
Programming
P9-15
<0034>
088E
Remove Delay Time
Remove Dly Time
Delay time before the lead drive is removed from the system. 0 ~ 3600 s 10 s Programming
P9-16
<0034>
088F
Stabilization Time
Stabilization Time
Time used to stabilize the system when a pump is staged or de-staged.
Lead-lag control and pump protection is suspended during this time.
0 ~ 3600 s 3 s Programming
Denotes that parameter can be changed when the drive is running.
Parameter
No.
Addr.
Hex
Parameter Name
Digital Operator
Display
Description
Setting
Range
Factory
Setting
Menu
Location
Page
No.
Produits connexes et manuels pour Équipement Yaskawa iQpump Controller Programming Manual
Équipement Yaskawa MP940 Manuel d'utilisateur
(522 pages)
(522 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels